Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Pontiac Aztek V6-3.4L VIN EFACTORY OEM SERVICE PROCEDURE
System Specifications
Fastener Tightening Specifications
| Accelerator Cable Bracket Retaining Bolts | 13 N.m |
| Accelerator Cable Bracket Retaining Nut | 10 N.m |
| Accelerator Pedal Retaining Bolt | 3 N.m |
| Air Cleaner Duct Clamp | 2 N.m |
| Air Cleaner Housing Bolt | 10 N.m |
| AIR Crossover Pipe Bolt | 29 N.m |
| AIR Shut-off Valve | 20 N.m |
| AIR Shut-off Valve Nut | 10 N.m |
| AIR Shut-oft Valve Pipe Adapter Bolt | 30 N.m |
| Camshaft Position (CMP) Sensor Retaining Bolt | 8 N.m |
| Crankshaft Position 7X (CKP) Sensor Bolts | 11 N.m |
| Crankshaft Position 24X (CI(P) Sensor Bolts | 10 N.m |
| Engine Coolant Temperature (ECT) Sensor | 20 N.m |
| EVAP Canister Bracket Retaining Nut | 10 N.m |
| EVAP Canister Purge Valve Bracket | 10 N.m |
| EVAP Canister Retaining Nut | 6 N.m |
| Exhaust Gas Recirculation Pipe Bolt | 25 N.m |
| Exhaust Gas Recirculation Pipe Nut | 25 N.m |
| Exhaust Gas Recirculation Valve Attaching Bolts | 30 N.m |
| Fuel Filler Pipe Attaching Nut | 25 N.m |
| Fuel Filler Pipe Attaching Screw | 25 N.m |
| Fuel Filler Pipe Clamp | 2.5 N.m |
| Fuel Filler Mounting Bracket Nut | 10 N.m |
| Fuel Pressure Regulator Attaching Bolt | 8.5 N.m |
| Fuel Pressure and Return Pipes | 17 N.m |
| Fuel Rail Attaching Nuts or Bolts | 10 N.m |
| Fuel Tank Filler Pipe Hose Clamp | 2.5 N.m |
| Fuel Tank Retaining Strap Bolts | 47 N.m |
| Heated Oxygen Sensors | 41 N.m |
| Idle Air Control Valve Attaching Screws | 3 N.m |
| Ignition Coil to Ignition Control Module Screws | 4.5 N.m |
| Ignition Controle Module Bracket to Engine Studs and Nuts | 25 N.m |
| knock Sensor | 19 N.m |
| Manifold Absolute Pressure (MAP) Sensor Retaining Bolt | 3 N.m |
| Powertrain Control Module (PCM) Harness Screws | 8 N.m |
| Secondary AIR Injection Check Valve Bracket Nut | 10 N.m |
| Secondary AIR Injection Check Valve Mounting Bolt | 10 N.m |
| Secondary AIR Injection Pipe Nut | 10 N.m |
| Secondary AIR Injection Pump Bracket Bolt | 50 N.m |
| Secondary AIR lnjection Vacuum Bleed Valve Bracket Nut | 10 N.m |
| Throttle Body Retaining Nuts or Bolts | 28 N.m |
| Throttle Position Sensor Screws | 2 N.m |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
