Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Pontiac Aztek V6-3.4L VIN EFACTORY OEM SERVICE PROCEDURE
Ride/Trim Height Specifications
| Front Wheel Drive | Vehicles with 215/70R15 Tires | Dimension D | 5.6-6.4 in. |
| Dimension J Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 9.3-10.1 in. | ||
| Dimension K Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 10.2-11.0 in. | ||
| Dimension Z | 2.1-2.9 in. | ||
| Vehicles with 215/65R16 Tires | Dimension D | 5.6-6.4 in. | |
| Dimension J Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 9.4-10.2 in. | ||
| Dimension K Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 10.3-11.1 in. | ||
| Dimension Z | 2.1-2.9 in. | ||
| Vehicles with 215/70R16 Tires | Dimension D | 5.6-6.4 in. | |
| Dimension J Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 9.8-10.6 in. | ||
| Dimension K Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 10.7-11.5 in. | ||
| Dimension Z | 2.1-2.9 in. | ||
| All Wheel Drive | Vehicles with 215/65R16 Tires | Dimension D | 3.4-4.2 in. |
| Dimension J Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 9.4-10.2 in. | ||
| Dimension K Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 9.8-10.6 in. | ||
| Dimension Z | 2.1-2.9 in. | ||
| Vehicles with 215/70R16 Tires | Dimension D | 3.4-4.2 in. | |
| Dimension J Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 9.8-10.6 in. | ||
| Dimension K Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle. | 10.7-11.4 in. | ||
| Dimension Z | 2.1-2.9 in. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
