2002 Pontiac Aztek V6-3.4L VIN EFACTORY OEM SERVICE PROCEDURE

Ride/Trim Height Specifications

Front Wheel Drive Vehicles with 215/70R15 Tires Dimension D 5.6-6.4 in.
Dimension J
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
9.3-10.1 in.
Dimension K
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
10.2-11.0 in.
Dimension Z 2.1-2.9 in.
Vehicles with 215/65R16 Tires Dimension D 5.6-6.4 in.
Dimension J
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
9.4-10.2 in.
Dimension K
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
10.3-11.1 in.
Dimension Z 2.1-2.9 in.
Vehicles with 215/70R16 Tires Dimension D 5.6-6.4 in.
Dimension J
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
9.8-10.6 in.
Dimension K
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
10.7-11.5 in.
Dimension Z 2.1-2.9 in.
All Wheel Drive Vehicles with 215/65R16 Tires Dimension D 3.4-4.2 in.
Dimension J
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
9.4-10.2 in.
Dimension K
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
9.8-10.6 in.
Dimension Z 2.1-2.9 in.
Vehicles with 215/70R16 Tires Dimension D 3.4-4.2 in.
Dimension J
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
9.8-10.6 in.
Dimension K
Measure the J dimension and the K dimension 650 mm (25.5 in.) from the centerline of the nearest wheel. These points are identified on the vertical surface of the rocker panel by a 2 mm (.08 in.) diameter 1mm (.04 in.) high circle.
10.7-11.4 in.
Dimension Z 2.1-2.9 in.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.