2002 Pontiac Aztek AWDFACTORY OEM SERVICE PROCEDURE

Data Definitions

WARNING: This page is about a different car, the 2004 GMC Sierra, 2004 GMC Cab & Chassis Sierra, 2004 Chevrolet Silverado, and 2004 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
Brake Pedal Travel - -50 to 200 mm (-1.97 to 7.87 in)

This data represents the chord length translation position of the brake pedal through its normal range of movement.

BPP Sensor Rate - 0 to +10%/25 ms

This data indicates the rate of change of the brake pedal.

BPP Sensor Input Voltage - 0 to 5 Volts

This data represents the voltage being supplied to the BPP Sensor as measured by the EHPS system.

BPP Sensor Output Voltage - 0 to 5 Volts

This data represents a raw brake pedal position indicated by the voltage being received by the EHPS module from the BPP Sensor as measured by the EHPS system.

EHPS 42 V Bus Voltage - 0 to 76 Volts

This data indicates the voltage of the 42 V bus at the EHPS module.

EHPS Ignition 0- OFF/ON

This data represents the voltage of the Accessory signal at the EHPS module as read by the EHPS system.

EHPS Ignition 1 - OFF/ON

This data represents the voltage of the Ignition 1 signal at the EHPS module as read by the EHPS system.

EHPS Demand - -100 to +100%

This data represents the percentage of the available EHPS pump output being delivered as determined by the EHPS system.

EHPS Demand Speed - 0 to +7500 RPM

This data represents the current pump speed being commanded as determined by the EHPS system.

EHPS ECU Temperature - -180 to +180°C (-238 to +302°F)

This data represents the temperature of the EHPS module in the EHPS system as determined by the EHPS system.

EHPS Manifold Temperature - -180 to +180°C (-238 to +302 °F)

This data represents the temperature of the manifold in the EHPS system as determined by the EHPS system.

EHPS Motor Current - 0 to +200 A

This data represents the current being used by the EHPS motor as measured by the EHPS system.

EHPS Motor RPM - 0 to +7500 RPM

This data represents the rotational speed of the EHPS motor as determined by the EHPS system.

Steering Wheel Rate - 0 to 2048°/s

This data represents the approximate degrees per second change of the steering wheel as determined by the EHPS system.

Steering Wheel Sensor Phase A Volts - Low/High

This data represents the state of the Phase A digital output of the steering wheel sensor at the EHPS unit as currently read by the EHPS system.

Steering Wheel Sensor Phase B Volts - Low/High

This data represents the state of the Phase B digital output of the steering wheel sensor at the EHPS unit as currently read by the EHPS system.

Vehicle Speed - km/h (mph)

This data represents the calculated speed of the vehicle as determined by the PCM.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.