Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Pontiac Sunfire L4-2.2L VIN 4FACTORY OEM SERVICE PROCEDURE
Windshield Washer Control Module: Service and Repair
REMOVAL PROCEDURE

1. Remove the lid completely from the washer solvent container.
2. Remove the left front headlight, if required, to access the top forward bolt.
3. Remove the top forward screw.

4. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
5. Remove the LF wheel.
6. Remove the splash shield.
7. Disconnect the electrical connector from the washer pump.
8. Disconnect the hose from the washer pump

9. Remove the two screws, the retainer and the washer solvent container with the air induction assembly from the vehicle.

10. Remove the screw and the air induction assembly from the washer solvent container.
INSTALLATION PROCEDURE
NOTE: Refer to Fastener Notice in Service Precautions

1. Install the air induction assembly onto the washer solvent container with the screw.

2. Install the washer solvent Container and the air induction assembly with the two screws and the retainer.
Tighten
Tighten the screws to 10 N.m (88 lb in).

3. Connect the hose to the washer pump.
4. Connect the electrical connector to the washer pump.
5. Install the splash shield.
6. Install the LF wheel.
7. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

8. Install the top forward screw.
Tighten
Tighten the screw to 10 N.m (88 lb in).
9. Install the left front headlight, if removed.
10. Install the lid on the container.
1. Remove the lid completely from the washer solvent container.
2. Remove the left front headlight, if required, to access the top forward bolt.
3. Remove the top forward screw.
4. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
5. Remove the LF wheel.
6. Remove the splash shield.
7. Disconnect the electrical connector from the washer pump.
8. Disconnect the hose from the washer pump
9. Remove the two screws, the retainer and the washer solvent container with the air induction assembly from the vehicle.
10. Remove the screw and the air induction assembly from the washer solvent container.
INSTALLATION PROCEDURE
NOTE: Refer to Fastener Notice in Service Precautions
1. Install the air induction assembly onto the washer solvent container with the screw.
2. Install the washer solvent Container and the air induction assembly with the two screws and the retainer.
Tighten
Tighten the screws to 10 N.m (88 lb in).
3. Connect the hose to the washer pump.
4. Connect the electrical connector to the washer pump.
5. Install the splash shield.
6. Install the LF wheel.
7. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
8. Install the top forward screw.
Tighten
Tighten the screw to 10 N.m (88 lb in).
9. Install the left front headlight, if removed.
10. Install the lid on the container.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
