Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Pontiac Sunfire L4-2.2L VIN 4FACTORY OEM SERVICE PROCEDURE
Plastic Tank
REMOVAL PROCEDURE

1. Relieve the fuel system pressure. Refer to the Fuel Pressure Relief Procedure. Service and Repair
2. Drain the fuel tank. Refer to Fuel Tank Draining Procedure.
3. Remove the fuel tank.
4. Remove the fuel sender assembly.
5. Remove the fuel pump and fuel level sender electrical retaining clip at the top of the modular fuel sender assembly.
6. Disconnect the fuel pump and fuel level sender electrical connector.
7. Depress the 3 tabs (2) securing upper fuel reservoir to the lower reservoir (1).

8. Depress the tab (1) and remove the upper reservoir from the lower reservoir.

9. Depress the tab (1) on the fuel level sensor (2).

10. Push the fuel level sensor (1) up and out of the housing.
11. Remove the retaining clip from the electrical connector.
12. Remove the fuel level sender wires from the connector, taking care to note the location of the wires.
INSTALLATION PROCEDURE
IMPORTANT:
^ Make sure the wires are routed under the fuel level sender.
^ Make sure the tab locks in place.

1. Install the fuel level sensor (1) by sliding it down in the housing.

2. Slide the upper reservoir into the lower reservoir (1) making sure the 3 tabs (2) lock in place.
3. Connect the 2 wires into the connector and lock it with the retaining clip.
4. Connect the fuel pump and fuel level sensor electrical connector and lock with it the retaining clip.
5. Reinstall the fuel sender assembly.
6. Reinstall the fuel tank.
7. Refill the fuel tank.
8. Reinstall the fuel fill cap.
9. Connect the negative battery cable.
10. Inspect for leaks using the following procedure:
10.1. Turn ON the ignition, with the engine OFF for 2 seconds.
10.2. Turn OFF the ignition for 10 seconds.
10.3. Turn ON the ignition, with the engine OFF.
10.4. Inspect for fuel leaks.
1. Relieve the fuel system pressure. Refer to the Fuel Pressure Relief Procedure. Service and Repair
2. Drain the fuel tank. Refer to Fuel Tank Draining Procedure.
3. Remove the fuel tank.
4. Remove the fuel sender assembly.
5. Remove the fuel pump and fuel level sender electrical retaining clip at the top of the modular fuel sender assembly.
6. Disconnect the fuel pump and fuel level sender electrical connector.
7. Depress the 3 tabs (2) securing upper fuel reservoir to the lower reservoir (1).
8. Depress the tab (1) and remove the upper reservoir from the lower reservoir.
9. Depress the tab (1) on the fuel level sensor (2).
10. Push the fuel level sensor (1) up and out of the housing.
11. Remove the retaining clip from the electrical connector.
12. Remove the fuel level sender wires from the connector, taking care to note the location of the wires.
INSTALLATION PROCEDURE
IMPORTANT:
^ Make sure the wires are routed under the fuel level sender.
^ Make sure the tab locks in place.
1. Install the fuel level sensor (1) by sliding it down in the housing.
2. Slide the upper reservoir into the lower reservoir (1) making sure the 3 tabs (2) lock in place.
3. Connect the 2 wires into the connector and lock it with the retaining clip.
4. Connect the fuel pump and fuel level sensor electrical connector and lock with it the retaining clip.
5. Reinstall the fuel sender assembly.
6. Reinstall the fuel tank.
7. Refill the fuel tank.
8. Reinstall the fuel fill cap.
9. Connect the negative battery cable.
10. Inspect for leaks using the following procedure:
10.1. Turn ON the ignition, with the engine OFF for 2 seconds.
10.2. Turn OFF the ignition for 10 seconds.
10.3. Turn ON the ignition, with the engine OFF.
10.4. Inspect for fuel leaks.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
