Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Pontiac Sunfire L4-2.2L VIN 4FACTORY OEM SERVICE PROCEDURE
Crankshaft Relearn Procedure
IMPORTANT: A Crankshaft Position (CKP) system variation learn procedure must be performed any time a change is made to the crankshaft sensor to crankshaft relationship. Changing the crank sensor to crankshaft relationship will not allow the PCM to detect misfire at all speeds and loads accurately, resulting in a possible false misfire DTC being set.
Removing a part for inspection and then reinstalling the same part is considered a disturbance. A false DTC P0300 could be set if the CKP position variation learn procedure is not performed.
The learn procedure is required after the following service procedures have been performed, regardless of whether or not DTC P1336 is set:
^ PCM replacement
^ Engine replacement
^ Crankshaft replacement
^ Crankshaft position sensor replacement
^ Any engine repairs which disturbs the crankshaft/harmonic balancer to the crankshaft position sensor relationship.
A fully warmed-up engine is critical to learning the variation correctly. If a valid learn occurs, no other learns can be completed on that ignition cycle.
If the engine cuts out before the specified learn procedure engine speed or at normal fuel cut-off RPM, the PCM is not in the learn procedure mode. Review the crankshaft position system variation learn procedure and re-enable the learn procedure. Verify that the scan tool displays Test in Progress.
CAUTION: When performing the Crankshaft Position System Variation Learning Procedure always set the vehicle parking brake and block the drive wheels in order to prevent personal injury. Release the throttle immediately when the engine starts to decelerate. Once the learn procedure is completed, engine control will be returned to the operator and the engine will respond to throttle position.
IMPORTANT: The battery must be fully charged and in good condition. The scan tool connection at the DLC is clean and tight before starting the Crankshaft Position System Variation Learn procedure.
1. Close the hood.
2. Block the drive wheels and set the vehicle parking brake.
3. Put the vehicle in Park or Neutral.
4. Turn all the accessories OFF.
5. Install a scan tool.
6. Start and run the engine until it is at the normal operating temperature of 74°C (165°F).
7. With the engine still running, enable the crankshaft position system variation learn procedure with the scan tool.
8. Press and hold the brake pedal firmly. Accelerate to Wide-open Throttle (WOT). Release the throttle when fuel cut-off is achieved.
9. Verify with the scan tool that the crankshaft variation has been learned.
If the variation will not learn, perform this procedure up to 3 times.
Removing a part for inspection and then reinstalling the same part is considered a disturbance. A false DTC P0300 could be set if the CKP position variation learn procedure is not performed.
The learn procedure is required after the following service procedures have been performed, regardless of whether or not DTC P1336 is set:
^ PCM replacement
^ Engine replacement
^ Crankshaft replacement
^ Crankshaft position sensor replacement
^ Any engine repairs which disturbs the crankshaft/harmonic balancer to the crankshaft position sensor relationship.
A fully warmed-up engine is critical to learning the variation correctly. If a valid learn occurs, no other learns can be completed on that ignition cycle.
If the engine cuts out before the specified learn procedure engine speed or at normal fuel cut-off RPM, the PCM is not in the learn procedure mode. Review the crankshaft position system variation learn procedure and re-enable the learn procedure. Verify that the scan tool displays Test in Progress.
CAUTION: When performing the Crankshaft Position System Variation Learning Procedure always set the vehicle parking brake and block the drive wheels in order to prevent personal injury. Release the throttle immediately when the engine starts to decelerate. Once the learn procedure is completed, engine control will be returned to the operator and the engine will respond to throttle position.
IMPORTANT: The battery must be fully charged and in good condition. The scan tool connection at the DLC is clean and tight before starting the Crankshaft Position System Variation Learn procedure.
1. Close the hood.
2. Block the drive wheels and set the vehicle parking brake.
3. Put the vehicle in Park or Neutral.
4. Turn all the accessories OFF.
5. Install a scan tool.
6. Start and run the engine until it is at the normal operating temperature of 74°C (165°F).
7. With the engine still running, enable the crankshaft position system variation learn procedure with the scan tool.
8. Press and hold the brake pedal firmly. Accelerate to Wide-open Throttle (WOT). Release the throttle when fuel cut-off is achieved.
9. Verify with the scan tool that the crankshaft variation has been learned.
If the variation will not learn, perform this procedure up to 3 times.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
