Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Pontiac Sunfire L4-2.2L VIN 4FACTORY OEM SERVICE PROCEDURE
Compressor Replacement
REMOVAL PROCEDURE
IMPORTANT: When replacing a failed compressor it will be necessary to inspect the expansion (orifice) tube for material build up. Clean or replace the expansion tube as necessary.

1. Recover the A/C system. Refer to Refrigerant Recovery and Recharging.
2. Remove the drive belt.
3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
4. Remove the right front wheelhouse splash shield.
5. Disconnect the compressor clutch electrical connector.
6. Remove the compressor hose assembly from the compressor.
7. Remove the compressor bolts (2) and (4).
8. Remove the compressor (3).
INSTALLATION PROCEDURE
IMPORTANT: When servicing or replacing the compressor, drain and measure the oil from the compressor.

1. Drain and measure the oil in the removed compressor, if replacing the compressor.
2. Refill the new compressor with the proper amount of NEW oil. Refer to Refrigerant Oil Distribution.
3. Install the compressor (3) to the compressor mounting bracket (1).
NOTE: Refer to Fastener Notice in Cautions and Notices.
4. Install the compressor mounting bolts (4) and (2).
Tighten
4.1. Tighten the front compressor mounting bolts (4) to 45 N.m (33 lb ft).
4.2. Tighten the rear compressor mounting bolt (2) to 65 N.m (48 lb ft).
5. Install the compressor hose assembly to the compressor.
6. Connect the clutch electrical connector.
7. Install the right front wheelhouse splash shield.
8. Lower the vehicle.
9. Install the drive belt.
10. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging.
11. Perform a leak test. Refer to Leak Testing.
12. Test the system operation.
IMPORTANT: When replacing a failed compressor it will be necessary to inspect the expansion (orifice) tube for material build up. Clean or replace the expansion tube as necessary.
1. Recover the A/C system. Refer to Refrigerant Recovery and Recharging.
2. Remove the drive belt.
3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
4. Remove the right front wheelhouse splash shield.
5. Disconnect the compressor clutch electrical connector.
6. Remove the compressor hose assembly from the compressor.
7. Remove the compressor bolts (2) and (4).
8. Remove the compressor (3).
INSTALLATION PROCEDURE
IMPORTANT: When servicing or replacing the compressor, drain and measure the oil from the compressor.
1. Drain and measure the oil in the removed compressor, if replacing the compressor.
2. Refill the new compressor with the proper amount of NEW oil. Refer to Refrigerant Oil Distribution.
3. Install the compressor (3) to the compressor mounting bracket (1).
NOTE: Refer to Fastener Notice in Cautions and Notices.
4. Install the compressor mounting bolts (4) and (2).
Tighten
4.1. Tighten the front compressor mounting bolts (4) to 45 N.m (33 lb ft).
4.2. Tighten the rear compressor mounting bolt (2) to 65 N.m (48 lb ft).
5. Install the compressor hose assembly to the compressor.
6. Connect the clutch electrical connector.
7. Install the right front wheelhouse splash shield.
8. Lower the vehicle.
9. Install the drive belt.
10. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging.
11. Perform a leak test. Refer to Leak Testing.
12. Test the system operation.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
