2000 Pontiac Firebird Trans Am, 2D Convertible, AutomaticFACTORY OEM SERVICE PROCEDURE

Powertrain Control Module Connector Terminal Identification (3.8L - LESABRE)

POWERTRAIN CONTROL MODULE CONNECTOR TERMINAL IDENTIFICATION (3.8L - LESABRE) (1)

Connector Terminal No. Wire Color Function
C1 1 BLK Sensor Return
C1 2 & 3 ..... Not Used
C1 4 LT GRN Shift Solenoid Valve "A" Control
C1 5 DK BLU Cooling Fan Relay No. 2 Control (High Speed)
C1 6 DK GRN Cooling Fan Relay No. 1 Control (Low Speed)
C1 7 BLK Camshaft Position PCM Input
C1 8 PPL/WHT Crankshaft Position 3x Sensor Reference
C1 9 LT BLU/BLK Crankshaft Position 18x Sensor Reference
C1 10 GRY Manifold Absolute Pressure Sensor 5-Volt Reference
C1 11 ..... Not Used
C1 12 BLK Engine Coolant Temperature Sensor Ground
C1 13 ORG/BLK Manifold Absolute Pressure Sensor Ground
C1 14 & 15 ..... Not Used
C1 16 BLK/WHT Powertrain Control Module Ground
C1 17 RED/BLK Intake Air Temperature Sensor Ground
C1 18 ..... Not Used
C1 19 WHT Ignition Positive Voltage (OFF/RUN/START)
C1 20 ORG Battery Positive Voltage
C1 21 ..... Not Used
C1 22 PNK Transaxle Fluid Pressure Switch "A" Input
C1 23-27 ..... Not Used
C1 28 TAN Heated Oxygen Sensor No. 2 Signal Low
C1 29 TAN Heated Oxygen Sensor No. 1 Signal Low
C1 30 PPL Torque Converter Clutch Brake Switch Input
C1 31 BLK EGR Pintle Position Sensor Ground
C1 32 GRY EGR Valve Control Ground
C1 33 DK BLU Bank No. 1 Knock Sensor Signal
C1 34 LT BLU Bank No. 2 Knock Sensor Signal
C1 35-37 ..... Not Used
C1 38 LT GRN/WHT Idle Air Control Valve "B" High
C1 39-42 ..... Not Used
C1 43 YEL/BLK Fuel Injector No. 6 Control Circuit
C1 44 YEL/BLK Shift Solenoid Valve "B" Control
C1 45 PNK/BLK Air Injection Reaction Solenoid Output
C1 46 LT BLU/BLK Fuel Injector No. 4 Control Circuit
C1 47 BLK/WHT Fuel Injector No. 5 Control Circuit
C1 48 RED/BLK Reference Low
C1 49-52 ..... Not Used
C1 53 TAN/BLK By-Pass Valve Control
C1 54 WHT Ignition Control
C1 55 DK GRN/WHT Vehicle Speed Sensor Output
C1 56 BLK/WHT Powertrain Control Module Ground
C1 57 BLK/WHT Powertrain Control Module Ground
C1 58 PPL Serial Data (Class 2)
C1 59 PPL Serial Data (Class 2)
C1 60 BLK/WHT Powertrain Control Module Ground
C1 61 BLK Throttle Position Sensor Ground
C1 62 DK BLU/WHT A/T Input Shaft Speed Sensor Low
C1 63 RED/BLK A/T Input Shaft Speed Sensor High
C1 64 YEL Vehicle Speed Sensor High
C1 65 PPL Vehicle Speed Sensor Low
C1 66 & 67 ..... Not Used
C1 68 YEL Transaxle Range Switch Input "B"
C1 69 YEL Mass Airflow Sensor Signal
C1 70 ..... Not Used
C1 71 ORG/BLK Traction Control Desired Torque Input
C1 72 DK GRN Cruise Control Disable/Inhibit Control
C1 73 LT GRN/BLK Fuel Injector No. 2 Control Circuit
C1 74 & 75 ..... Not Used
C1 76 DK GRN/WHT EVAP Canister Purge Control
C1 77 & 78 ..... Not Used
C1 79 BLK Fuel Injector No. 1 Control Circuit
C1 80 BLK Sensor Return (Engine Oil Pressure)
C2 1 ..... Not Used
C2 2 WHT EVAP Canister Vent Valve Control
C2 3 DK GRN/WHT Fuel Pump Relay Control
C2 4 WHT EGR Valve Control
C2 5 BRN/WHT Malfunction Indicator Light Control
C2 6 ..... Not Used
C2 7 LT BLU/WHT Idle Air Control Valve "A" High
C2 8 WHT Tachometer Signal
C2 9 TAN/BLK Traction Control Delivered Torque Control
C2 10 PPL Heated Oxygen Sensor No. 1 Signal High
C2 11 PPL Heated Oxygen Sensor No. 2 Signal High
C2 12-15 ..... Not Used
C2 16 WHT Transaxle Range Switch Input "P"
C2 17 RED Transmission Fluid Pressure Switch "C"
C2 18 BLK/WHT Transaxle Range Switch Input "A"
C2 19-22 ..... Not Used
C2 23 PPL Crank Signal
C2 24 PNK Ignition Positive Voltage
C2 25 LT GRN Manifold Absolute Pressure Sensor Signal
C2 26 YEL Engine Coolant Temperature Sensor Signal
C2 27 RED/BLK A/C Refrigerant Pressure Sensor Signal
C2 28 BRN EGR Valve Pintle Position Signal
C2 29 GRY Generator Terminal "F" Monitor
C2 30 GRY EGR Valve 5-Volt Reference "A"
C2 31 ..... Not Used
C2 32 GRY Engine Oil Pressure 5-Volt Reference "A"
C2 33 GRY Fuel Level/Throttle Position Sensor 5-Volt Reference "A"
C2 34 GRY A/C Pressure/Fuel Tank Pressure Sensor 5-Volt Reference "B"
C2 35 BLK Sensor Ground
C2 36-38 ..... Not Used
C2 39 DK GRN/WHT A/C Compressor Clutch Relay Control
C2 40 & 41 ..... Not Used
C2 42 PNK/BLK Fuel Injector No. 3 Control Circuit
C2 43 ..... Not Used
C2 44 LT BLU/BLK Idle Air Control Valve "A" Low
C2 45 RED/BLK Pressure Control Solenoid High
C2 46 LT BLU/WHT Pressure Control Solenoid Low
C2 47 & 48 ..... Not Used
C2 49 LT GRN/BLK Idle Air Control Valve "B" Low
C2 50 TAN Intake Air Temperature Sensor Signal
C2 51 & 52 ..... Not Used
C2 53 TAN/WHT Oil Pressure Sensor Signal
C2 54 ..... Not Used
C2 55 DK GRN Fuel Tank Pressure Sensor Signal
C2 56 GRY Transaxle Range Switch Input "C"
C2 57 DK BLU Transaxle Fluid Pressure Switch "B"
C2 58 BRN Engine Oil Level Sensor Signal
C2 59 LT BLU/BLK Cruise Control Status
C2 60 GRY Brake Pedal Switch Output (Extended Travel)
C2 61 RED Generator Terminal "L" Control
C2 62 ..... Not Used
C2 63 YEL Torque Converter Clutch Release Switch Input
C2 64 & 65 ..... Not Used
C2 66 DK BLU Throttle Position Sensor Signal
C2 67 ..... Not Used
C2 68 YEL/BLK Transaxle Fluid Temperature Sensor
C2 69 PPL Fuel Level Input
C2 70-74 ..... Not Used
C2 75 BRN Air injection Reaction Pump Motor Relay Output Coil
C2 76 YEL/BLK Starter Relay Output Coil
C2 77 GRY Boost Control Solenoid Control
C2 78 BRN Torque Converter Clutch PWM Solenoid Control
C2 79 & 80 ..... Not Used
(1) See Figure.
Chapter Navigation
Return to Chapter: Powertrain Control Module Connector Terminal Identification
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.