2000 Pontiac Firebird Formula, AutomaticFACTORY OEM SERVICE PROCEDURE

Specifications Index

CAMARO & FIREBIRD SPECIFICATIONS INDEX

System Specifications/Procedure
Air Conditioning
Service SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Battery NA
Brakes
Bleeding Sequence BLEEDING BRAKE SYSTEM
Disc Brakes DISC BRAKE SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Charging
Generator CHARGING SYSTEM TEST
Torque TORQUE SPECIFICATIONS
Drive Belts
Adjustment BELT ADJUSTMENT
Belt Routing See appropriate illustration under SERPENTINE BELT ROUTING & ALIGNMENT
Engine Cooling
Service COOLING SYSTEM SPECIFICATIONS
Radiator Pressure Cap 18 psi
Thermostat R&I
3.8L THERMOSTAT REPLACEMENT
5.7L NA
Water Pump R&I
3.8L TORQUE SPECIFICATIONS
5.7L WATER PUMP
Engine Mechanical
3.8L
Compression Lowest compression reading should not be less than 70 percent of highest compression reading. No cylinder compression reading should be less than 100 psi (7.0 kg/cm2 ).
Oil Pressure With engine at normal operating temperature, oil pressure (with 5W-30 or 10W-30 engine oil) should be 60 psi (4.2 kg/cm2 ) at 1850 RPM.
Overhaul ENGINE SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
5.7L
Compression Lowest compression reading should not be less than 70 percent of highest compression reading. No cylinder compression reading should be less than 100 psi (7.0 kg/cm2 ).
Oil Pressure With engine at normal operating temperature, oil pressure should be at least 6 psi (0.4 kg/cm2 ) at 1000 RPM, 18 psi (1.3 kg/cm2 ) at 2000 RPM and 24 psi (1.7 kg/cm2 ) at 4000 RPM.
Overhaul ENGINE SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Fluid Specifications See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button.
Flywheel/Flex Plate Torque
3.8L
Step 1 11 ft. lbs. (15 N.m)
Step 2 Additional 50 Degrees
5.7L Tighten bolts evenly using a crisscross sequence
Step 1 15 ft. lbs. (20 N.m)
Step 2 37 ft. lbs. (50 N.m)
Step 3 74 ft. lbs. (100 N.m)
Fuel System
Pressure On 3.8L 48-55 psi (3.4-3.9 kg/cm2 )
On 5.7L 55-60 psi (3.9-4.2 kg/cm2 )
Fuel Pressure Test Procedure FUEL SYSTEM PRESSURE TEST (EXCEPT SATURN)
Fuel Filter Location and R & I REMOVAL PROCEDURE (CAMARO, FIREBIRD)
Ignition
Firing Order & Cylinder Identification See FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance) 1000-1500 ohms per foot
Ignition Wires (Routing) For coil/wire routing, see appropriate illustration under FIRING ORDER
Spark Plugs
3.8L
Type AC Part No. 41-921
Gap .060 in. (1.52 mm)
Torque 20 ft. lbs. (27 N.m)
5.7L
Type AC Part No. 41-931
Gap Iridium .040 in. (1.04 mm)
Platinum .060 in. (1.52 mm)
Torque Tighten to 15 ft. lbs. (20 N.m) when using NEW cylinder head. Tighten to 11 ft. lbs. (15 N.m) for all subsequent installations.
Starting
Starter ON-VEHICLE TESTING
Torque TORQUE SPECIFICATIONS
Wheel Alignment
Adjustment Specifications WHEEL ALIGNMENT SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Wheel & Tire
Lug Nut Torque 100 ft. lbs. (136 N.m)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.