Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1992 Pontiac LeMans VLFACTORY OEM SERVICE PROCEDURE
Diagnostic Circuit Check
NOTE:
Perform diagnostic circuit check to diagnose SERVICE ENGINE SOON light function, ALDL connector and no-start condition.
- Compare data from vehicle being tested with SCAN TESTER DATA table. This ensures self-diagnostic system is working properly. With ignition on and engine off, observe SERVICE ENGINE SOON light. If Code 12 is flashing, check for grounded diagnostic test circuit (ALDL terminal "B"). See wiring schematic in CHART A-2. If SERVICE ENGINE SOON light is off, go to CHART A-1. If a steady SERVICE ENGINE SOON light is present, jump ALDL terminal "B" to terminal "A".
- The SERVICE ENGINE SOON light should flash a Code 12. If Code 12 is not present, go to CHART A-2. If Code 12 is present, check if scan tester displays ECM data. If no data is displayed, go to CHART A-2.
- Start engine. If engine does not start, go to CHART A-3 in BASIC TESTING article in this section. If engine starts, check for fault codes. If fault codes are present, see applicable chart under CODE CHARTS. Start with lowest code. If no fault codes are present, compare scan tester data with typical data values. See SCAN TESTER DATA table. Values should be within typical ranges.
- If values are okay, see TESTS W/O CODES article in this section. If values are not within typical ranges, see I - SYS/COMP TESTS article in this section.
SCAN TESTER DATA(1)
| Scan Position | Units Displayed | Typical Value | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Engine Speed | RPM | (2) 0-200 RPM | ||||||||||||||
| Desired Idle | RPM | (3) ECM Idle | ||||||||||||||
| Coolant Temp | °C | 85-105° | ||||||||||||||
| MAP | Volts | (4) 1.0-2.0 | ||||||||||||||
| Open/Closed Loop | Open/Closed Loop | (5) Closed Loop | ||||||||||||||
| TPS | Volts | .45-1.25 | ||||||||||||||
| Throttle Angle | 0-100% | 0 | ||||||||||||||
| Oxygen Sensor | mV | (6) 100-1000 | ||||||||||||||
| Inj. Pulse Width | Milliseconds | .8-3.0 | ||||||||||||||
| Spark Advance | Degrees | Varies | ||||||||||||||
| Fuel Integrator | Counts | 110-145 | ||||||||||||||
| Block Learn | Counts | 118-138 | ||||||||||||||
| Idle Air Control | Counts/Steps | 1-50 | ||||||||||||||
| Park/Neutral | PNRDL | P or N | ||||||||||||||
| MPH & km/h | 0-255 | 0 | ||||||||||||||
| Torque Conv. Clutch | On/Off | Off | ||||||||||||||
| Battery Voltage | Volts | 13.5-14.5 | ||||||||||||||
| Cooling Fan Relay | On/Off | (7) Off | ||||||||||||||
| A/C Request | Yes/No | No | ||||||||||||||
| A/C Clutch | On/Off | Off | ||||||||||||||
| Shift Light (M/T) | On/Off | Off | ||||||||||||||
|
||||||||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
