Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1991 Pontiac LeMans BaseFACTORY OEM SERVICE PROCEDURE
Diagnostic Circuit Check
NOTE:
Perform diagnostic circuit check to diagnose CHECK ENGINE light function, ALDL connector and no-start condition.
- Compare data from vehicle being tested with SCAN TESTER DATA table. This ensures self-diagnostic system is working properly. With ignition on and engine off, observe CHECK ENGINE light. If Code 12 is flashing, check for grounded diagnostic test circuit No. 451. See DIAGNOSTIC CHARTS, CHART A-2, for wiring schematic. If CHECK ENGINE light is off, See DIAGNOSTIC CHARTS, CHART A-1. If a steady CHECK ENGINE light is present, jump ALDL terminal "B" to terminal "A".
- The CHECK ENGINE light should flash a Code 12. If Code 12 is not present, See DIAGNOSTIC CHARTS, CHART A-2. If Code 12 is present, check if Scan tester displays ECM data. If no data is displayed, See DIAGNOSTIC CHARTS, CHART A-2.
- Start engine. If engine does not start, See DIAGNOSTIC CHARTS, CHART A-3. If engine starts, check for fault codes. If fault codes are present, see applicable chart under DIAGNOSTIC CODE CHARTS. Start with lowest code. If no fault codes are present, compare Scan tester data with typical data values. See SCAN TESTER DATA table. Values should be within typical ranges.
- If values are okay, see TESTS W/O CODES article in this section. If values are not within typical ranges, refer to the SYSTEM/COMPONENT TESTS article in this section.
SCAN TESTER DATA
| Scan Position | Units Displayed | Typical Value | ||||||||||||||
| Engine Speed | RPM | (2) 0-200 RPM | ||||||||||||||
| Desired Idle | RPM | (3) ECM Idle | ||||||||||||||
| Coolant Temp | °C | 85-105° | ||||||||||||||
| Map | Volts | (4) 1.0-2.0 | ||||||||||||||
| Open/Closed Loop | Open/Closed Loop | (5) Closed Loop | ||||||||||||||
| TPS | Volts | .45-1.25 | ||||||||||||||
| Throttle Angle | 0-100% | 0 | ||||||||||||||
| Oxygen Sensor | mV | (6) 100-1000 | ||||||||||||||
| Inj. Pulse Width | Milliseconds | .8-3.0 | ||||||||||||||
| Spark Advance | Degrees | Varies | ||||||||||||||
| Fuel Integrator | Counts | 110-145 | ||||||||||||||
| Block Learn | Counts | 118-138 | ||||||||||||||
| Idle Air Control | Counts/Steps | 1-50 | ||||||||||||||
| Park/Neutral | PNRDL | P or N | ||||||||||||||
| MPH & km/h | 0-255 | 0 | ||||||||||||||
| Torque Conv. Clutch | On/Off | Off | ||||||||||||||
| Battery Voltage | Volts | 13.5-14.5 | ||||||||||||||
| Cooling Fan Relay | On/Off | (7) Off | ||||||||||||||
| A/C Request | Yes/No | No | ||||||||||||||
| A/C Clutch Shift Light (M/T) | On/Off | Off | ||||||||||||||
|
||||||||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
