Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1985 Oldsmobile Cutlass 442FACTORY OEM SERVICE PROCEDURE
Quick Lookups: Fluids
| FLUID CAPACITIES | |||||||
|---|---|---|---|---|---|---|---|
| Fluid Type | Application | Standard | Metric | Fluid Spec | Note | S/H | |
| Automatic Transmission Fluid | Trans Mfr CD 200-4R/MW9 | Overhaul | 11.00 QTS. | 10.4 L | Automatic Transmission Fluid DEXRON VI | Refer to TSB No. 04-07-30-037C, Date of Issue: April 11, 2007. | S |
| Automatic Transmission Fluid | Trans Mfr CD 200-4R/MW9 | Pan Removal and Replacement | 3.50 QTS. | 3.31 L | Automatic Transmission Fluid DEXRON VI | Refer to TSB No. 04-07-30-037C, Date of Issue: April 11, 2007. | S |
| Brake Fluid | N/A | N/A | DOT 3 Brake Fluid | GM Part No. 12377967 or DOT 3 equivalent. | S | ||
| Differential Gear Oil | 7.5 Inch Ring Gear | 3.50 PTS. | 1.65 L | Rear Axle Gear Oil | GM Part No. 1052271 or GM Part No. 1052272. | S | |
| Differential Gear Oil | w/8.5 Inch Ring Gear | 4.25 PTS. | 2.01 L | Rear Axle Gear Oil | GM Part No. 1052271 or GM Part No. 1052272. | S | |
| Engine Coolant | 5.0L Eng,Eng VIN 9 | 15.50 QTS. | 14.66 L | 50/50 mixture of Ethylene Glycol Base Antifreeze and water | GM Specification 1825-M. | S | |
| Engine Oil | 5.0L Eng | 4.00 QTS. | 3.78 L | SAE 5W-30 (Below -20Deg.F to 60Deg.F), 10W-30 & 10W-40 (0Deg.F to over 100Deg.F), 15W-40 (15Deg.F to over 100Deg.F), 20W-20 (20Deg.F to over 100Deg.F), 30 (40Deg.F to over 100Deg.F) | S | ||
| Fuel Tank | Gas | 18.00 GALS. | 68.13 L | S | |||
| Power Steering Fluid | Gas | Complete System | 2.25 PTS. | 1.06 L | GM Power Steering Fluid | GM Part No. 1050017. | S |
| Power Steering Fluid | w/Pump | 1.00 PTS. | 0.47 L | GM Power Steering Fluid | GM Part No. 1050017. | S | |
| Windshield Washer Fluid | N/A | N/A | Optikleen Windshield Washer Fluid | Follow the Manufacturer's Instructions for the mixture ratio. | S | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
