2017 Nissan-Datsun Versa Note S PlusFACTORY OEM SERVICE PROCEDURE

System Description: System: Fail-Safe

BCM performs fail-safe control when the following DTCs are detected.

CONSULT Display Fail - safe Cancellation
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF
B2196: DONGLE NG Inhibit engine cranking Erase DTC
B2198: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2557: VEHICLE SPEED - When the following CAN signal status (vehicle speed signal) becomes consistent
  • Vehicle speed signal (ABS)
  • Vehicle speed signal (Meter)
B2601: SHIFT P SIGNAL - 500 ms after the following signal reception status becomes consistent
  • Park position switch signal
  • P range signal (CAN)
B2602: SHIFT P DIAG - 5 seconds after the following BCM recognition conditions are fulfilled
  • Ignition switch is in the ON position
  • Park position switch signal: P position (push selector button) or except P position (9 - 16 V)
  • Vehicle speed: 4 km/h (2.5 MPH) or more
B2603: SHIFT POSITION - 500 ms after any of the following BCM recognition conditions are fulfilled
  • Status 1
    • Ignition switch is in the ON position
    • Park position switch signal: P position (push selector button) or except P position (9 - 16 V)
    • P/N position signal: Except P and N positions (0 - 1.5 V)
  • Status 2
    • Ignition switch is in the ON position
    • Park position switch signal: P position (release selector button) (0 - 1.5 V)
    • P/N position signal: P or N positions (9 - 16 V)
B2604: SHIFT PN DIAG CAN - 500 ms after any of the following BCM recognition conditions are fulfilled
  • Status 1
    • Ignition switch is in the ON position
    • P/N position signal: P or N position (9 - 16 V)
    • Shift position signal (CAN): P or N position
  • Status 2
    • Ignition switch is in the ON position
    • P/N position signal: Except P and N positions (0 - 1.5 V)
    • Shift position signal (CAN): Except P and N position
B2605: SHIFT PN DIAG IPDM - 500 ms after any of the following BCM recognition conditions are fulfilled
  • Status 1
    • Ignition switch is in the ON position
    • P/N position signal: Except P and N positions (0 - 1.5 V)
  • Status 2
    • Ignition switch is in the ON position
    • P/N position signal: P or N position (9 - 16 V)
B2608: STARTER RELAY Inhibit engine cranking 500 ms after the following signal communication status becomes consistent
  • Starter motor relay control signal
  • Starter relay status signal (CAN)
B260F: ECM CAN COMM Inhibit engine cranking When any of the following conditions are fulfilled
  • Ignition switch changes to ACC
  • Receives engine status signal (CAN)
B26F1: IGN RELAY OFF Inhibit engine cranking When the following conditions are fulfilled
  • Ignition switch ON signal (CAN: Transmitted from BCM): ON
  • Ignition switch ON signal (CAN: Transmitted from IPDM E/R): ON
B26F2: IGN RELAY ON Inhibit engine cranking When the following conditions are fulfilled
  • Ignition switch ON signal (CAN: Transmitted from BCM): OFF
  • Ignition switch ON signal (CAN: Transmitted from IPDM E/R): OFF
B26F3: START CONT RLY ON Inhibit engine cranking When the following conditions are fulfilled
  • Starter control relay signal (CAN: Transmitted from BCM): OFF
  • Starter control relay signal (CAN: Transmitted from IPDM E/R): OFF
B26F4: START CONT RLY OFF Inhibit engine cranking When the following conditions are fulfilled
  • Starter control relay signal (CAN: Transmitted from BCM): ON
  • Starter control relay signal (CAN: Transmitted from IPDM E/R): ON
B26F7: BCM Inhibit engine cranking by Intelligent Key system When room antenna and luggage room antenna functions normally
U0415: VDC CAN CIR2 - When vehicle speed signal (Meter) (CAN) is received normally
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.