2017 Nissan-Datsun Maxima SLFACTORY OEM SERVICE PROCEDURE

Data Monitor

Monitor Item [Unit] Main Description
REQ SW -DR [On/Off] * Indicates condition of door request switch LH
REQ SW -AS [On/Off] * Indicates condition of door request switch RH
REQ SW -BD/TR [On/Off] * Indicates condition of trunk opener request switch
PUSH SW [On/Off]   Indicates condition of push button ignition switch
SHFTLCK SLNID PWR SPLY [On/Off]   Indicates condition of shiftlock solenoid power supply
BRAKE SW 1 [On/Off] * Indicates condition of brake switch
BRAKE SW 2 [On/Off]   Indicates condition of brake switch
DETE/CANCL SW [On/Off] * Indicates condition of P position
SFT PN/N SW [On/Off] * Indicates condition of P or N position
UNLK SEN -DR [On/Off] * Indicates condition of door unlock sensor
PUSH SW -IPDM [On/Off]   Indicates condition of push button ignition switch received from IPDM E/R on CAN communication line
IGN RLY1 -F/B [On/Off]   Indicates condition of ignition relay 1 received from IPDM E/R on CAN communication line
DETE SW -IPDM [On/Off]   Indicates condition of detent switch received from TCM on CAN communication line
SFT PN -IPDM [On/Off]   Indicates condition of P or N position from TCM on CAN communication line
SFT P -MET [On/Off]   Indicates condition of P position from TCM on CAN communication line
SFT N -MET [On/Off]   Indicates condition of N position from IPDM E/R on CAN communication line
ENGINE STATE [Stop/Start/Crank/Run] * Indicates condition of engine state from ECM on CAN communication line
VEH SPEED 1 [mph/km/h] * Indicates condition of vehicle speed signal received from ABS on CAN communication line
VEH SPEED 2 [mph/km/h] * Indicates condition of vehicle speed signal received from combination meter on CAN communication line
DOOR STAT -DR [LOCK/READY/UNLK] * Indicates condition of driver side door status.
DOOR STAT -AS [LOCK/READY/UNLK] * Indicates condition of passenger side door status.
DOOR STAT -RR [LOCK/READY/UNLK] * Indicates condition of rear right side door status.
DOOR STAT -RL [LOCK/READY/UNLK] * Indicates condition of rear left side door status.
ID OK FLAG [Set/Reset]   Indicates condition of Intelligent Key ID
PRMT ENG START [Set/Reset]   Indicates condition of engine start possibility from Intelligent Key
I-KEY OK FLAG [Set/Reset]   Indicates condition of Intelligent Key ID.
ID AUTHENT CANCEL TIMER [under a stop]   Indicates condition of Intelligent Key ID authentication.
ACC BATTERY SAVER [under a stop]   Indicates condition of battery saver.
CRNK PRBT TMR [On/Off]   Indicates condition of crank prohibit timer.
AUT CRNK TMR [On/Off]   Indicates condition of automatic engine crank timer from Intelligent Key.
CRANKING TME [sec]   Indicates condition of engine cranking time from Intelligent Key.
SHORT CRANK   Indicates condition of condition of short crank from Intelligent Key
ST RLY -REQ   Indicates condition of starter relay.
IGN RLY 1 -REQ   Indicates condition of ignition 1 relay.
IGN RLY 2 -REQ   Indicates condition of ignition 2 relay.
DETE SW PWR [On/Off]   Indicates condition of park position switch voltage.
IGN RLY 3 -REQ   Indicates condition of ignition 3 relay.
ACC RLY -REQ   Indicates condition of ACC relay.
PRBT ENG STRT [Set/Reset]   Indicates condition of engine start possibility.
PRMT RKE STRT [Set/Reset]   Indicates condition of engine start possibility from Intelligent Key.
TRNK/HAT MNTR [On/Off]   Indicates condition of trunk lid.
RKE-LOCK [On/Off]   Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off]   Indicates condition of unlock signal from Intelligent Key.
RKE-TR/BD [On/Off]   Indicates condition of trunk open signal from Intelligent Key.
RKE-PANIC [On/Off]   Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off]   Indicates condition of mode change signal from Intelligent Key.
RKE OPE COUN1 [0-19] * When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19] * When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.