2016 Nissan-Datsun Versa Note SLFACTORY OEM SERVICE PROCEDURE

EBD Function

ABS warning lamp, brake warning lamp and SLIP indicator lamp in combination meter turn ON when a malfunction occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC, TCS, ABS and EBD functions.

DTC Malfunction detected condition Fail-safe condition
C1101 When an open circuit is detected in rear RH wheel sensor circuit. The following functions are suspended:
  • VDC
  • ABS
  • EBD (only when both rear wheels are malfunctioning)
C1102 When an open circuit is detected in rear LH wheel sensor circuit.
C1103 When an open circuit is detected in front RH wheel sensor circuit.
C1104 When an open circuit is detected in front LH wheel sensor circuit.
C1105
  • When a short circuit is detected in rear RH wheel sensor circuit.
  • When power supply voltage of rear RH wheel sensor is in following state:
    • Rear RH wheel sensor power supply voltage: 7.2 V ≥ Rear RH wheel sensor power supply voltage
  • When distance between rear RH wheel sensor and rear RH wheel sensor rotor is large.
  • When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not normal.
C1106
  • When a short circuit is detected in rear LH wheel sensor circuit.
  • When power supply voltage of rear LH wheel sensor is in following state:
    • Rear LH wheel sensor power supply voltage: 7.2 V ≥ Rear LH wheel sensor power supply voltage
  • When distance between rear LH wheel sensor and rear LH wheel sensor rotor is large.
  • When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not normal.
C1107
  • When a short circuit is detected in front RH wheel sensor circuit.
  • When power supply voltage of front RH wheel sensor is in following state:
    • Front RH wheel sensor power supply voltage: 7.2 V ≥ Front RH wheel sensor power supply voltage
  • When distance between front RH wheel sensor and front RH wheel sensor rotor is large.
  • When installation of front RH wheel sensor or front RH wheel sensor rotor is not normal.
C1108
  • When a short circuit is detected in front LH wheel sensor circuit.
  • When power supply voltage of front LH wheel sensor is in following state:
    • Front LH wheel sensor power supply voltage: 7.2 V ≥ Front LH wheel sensor power supply voltage
  • When distance between front LH wheel sensor and front LH wheel sensor rotor is large.
  • When installation of front LH wheel sensor or front LH wheel sensor rotor is not normal.
C1109
  • When ignition power supply voltage is in following state:
    • Ignition power supply voltage: 10 V ≥ Ignition power supply voltage.
    • Ignition power supply voltage: 16 V ≤ Ignition power supply voltage.
 The following functions are suspended:
  • VDC
  • TCS
  • ABS
  • EBD
C1110 When there is an internal malfunction in the ABS actuator and electric unit (control unit).
C1111 When a malfunction is detected in motor or motor relay. The following functions are suspended:
  • VDC
  • TCS
  • ABS
C1115 When difference in wheel speed between any wheel and others is detected when the vehicle is driven, because of installation of tires other than specified. The following functions are suspended:
  • VDC
  • TCS
  • ABS
  • EBD
C1116 When stop lamp switch signal is not input when brake pedal operates. The following functions are suspended:
  • VDC
  • TCS
C1120 When a malfunction is detected in front LH ABS IN valve. The following functions are suspended:
  • VDC
  • TCS
  • ABS
  • EBD
C1121 When a malfunction is detected in front LH ABS OUT valve.
C1122 When a malfunction is detected in front RH ABS IN valve.
C1123 When a malfunction is detected in front RH ABS OUT valve.
C1124 When a malfunction is detected in rear LH ABS IN valve.
C1125 When a malfunction is detected in rear LH ABS OUT valve.
C1126 When a malfunction is detected in rear RH ABS IN valve.
C1127 When a malfunction is detected in rear RH ABS OUT valve.
C1130 When a malfunction is detected in ECM system. The following functions are suspended:
  • VDC
  • TCS
C1140 When a malfunction is detected in actuator relay. The following functions are suspended:
  • VDC
  • TCS
  • ABS
  • EBD
C1142 When a malfunction is detected in VDC pressure sensor. The following functions are suspended:
  • VDC
  • TCS
C1143 When a malfunction is detected in steering angle sensor.
C1144 When neutral position adjustment of steering angle sensor is not complete.
C1145 When a malfunction is detected in yaw rate signal, or signal line of yaw rate/side/decel G sensor is open or shorted.
C1146 When a malfunction is detected in side G signal, or signal line of yaw rate/side/decel G sensor is open or shorted.
C1153 When ABS actuator and electric unit (control unit) is malfunctioning. (Pressure increase is too much or too little.) The following functions are suspended:
  • VDC
  • TCS
  • ABS
C1155 When brake fluid level low signal is detected. The following functions are suspended:
  • VDC
  • TCS
C1164 When a malfunction is detected in cut valve 1. The following functions are suspended:
  • VDC
  • TCS
  • ABS
  • EBD
C1165 When a malfunction is detected in cut valve 2.
C1166 When a malfunction is detected in suction valve 1.
C1167 When a malfunction is detected in suction valve 2.
C1170 When the information in ABS actuator and electric unit (control unit) is not the same. The following functions are suspended:
  • VDC
  • TCS
  • ABS
U1000 When CAN communication signal is not continuously transmitted or received for 2 seconds or more. The following functions are suspended:
  • VDC
  • TCS
U1002 When ABS actuator and electric unit (control unit) is not transmitting or receiving CAN communication signal for 2 seconds or less.
U1010 When detecting error during the initial diagnosis of CAN controller of ABS actuator and electric unit (control unit)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.