Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Detailed Flow
- INTERVIEW THE CUSTOMER
Clarify customer concerns before inspection. First of all, perform an interview utilizing DIAGNOSTIC WORK SHEET and reproduce the symptom as well as fully understand it. Ask customer about his/her concerns carefully. Check symptoms by driving vehicle with customer, if necessary.
CAUTION:Customers are not professional. Never guess easily like "maybe the customer means that...," or " maybe the customer mentions this symptom".
GO TO STEP 2 .
- CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained in the interview. Also check that the symptom is not caused by fail-safe mode. Refer to FAIL-SAFE .
CAUTION:When the symptom is caused by normal operation, fully inspect each portion and obtain the understanding of customer that the symptom is not caused by a malfunction.
GO TO STEP 3 .
- PERFORM THE SELF-DIAGNOSIS
With CONSULT
- Turn the ignition switch OFF → ON.CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
- Perform "Self Diagnostic Result" of "ABS".
Is DTC detected?
YES
Record or print Self Diagnostic Results and Freeze Frame Data (FFD). GO TO STEP 4 .
NO
GO TO STEP 6 .
- Turn the ignition switch OFF → ON.
- RECHECK THE SYMPTOM
- Erase "Self Diagnostic Result" of "ABS".
- Turn the ignition switch OFF → ON → OFF.CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
- Perform DTC confirmation procedures for the malfunctioning system.NOTE:
If some DTCs are detected at the some time, determine the order for performing the diagnosis based on DTC INSPECTION PRIORITY CHART .
Is DTC detected?
YES
GO TO STEP 5 .
NO
Check harness and connectors based on the information obtained in the interview. Refer to INTERMITTENT INCIDENT .
- REPAIR OR REPLACE MALFUNCTIONING COMPONENT
- Repair or replace malfunctioning components.
- Reconnect component or connector after repairing or replacing.
- When DTC is detected, erase "Self Diagnostic Result" of "ABS".CAUTION:
- Turn the ignition switch OFF → ON → OFF after erasing Self Diagnostic Result.
- Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
GO TO STEP 7 .
- IDENTIFY MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Identify malfunctioning system based on symptom diagnosis and perform inspection.
Can the malfunctioning system be identified?
YES
GO TO STEP 7 .
NO
Check harness and connectors based on the information obtained in the interview. Refer to INTERMITTENT INCIDENT .
- FINAL CHECK
- Select "DATA MONITOR" of "ABS"
- Check the reference values. Refer to REFERENCE VALUE .
- Recheck the symptom and check that the symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES
GO TO STEP 3 .
NO
Inspection End.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.