2016 Nissan-Datsun Sentra SLFACTORY OEM SERVICE PROCEDURE

Data Monitor

Monitor Item [Unit] Main Description
REQ SW -DR [On/Off] * Indicates condition of door request switch LH.
REQ SW -AS [On/Off] * Indicates condition of door request switch RH.
REQ SW -BD/TR [On/Off] * Indicates condition of trunk open switch.
PUSH SW [On/Off]   Indicates condition of push-button ignition switch.
CLUCH SW [On/Off] * Indicates condition of clutch switch.
BRAKE SW 1 [On/Off] * Indicates condition of brake switch.
BRAKE SW 2 [On/Off]   Indicates condition of brake switch.
DETE/CANCL SW [On/Off] * Indicates condition of P (park) position.
SFT PN/N SW [On/Off] * Indicates condition of P (park) or N (neutral) position.
UNLK SEN -DR [On/Off] * Indicates condition of driver door unlock sensor.
PUSH SW -EPDM [On/Off]   Indicates condition of push-button ignition switch received from EPDM E/R on CAN communication line.
IGN RLY1 -F/B [On/Off]   Indicates condition of ignition relay 1 received from EPDM E/R on CAN communication line.
DETE SW -EPDM [On/Off]   Indicates condition of detent switch received from TCM on CAN communication line.
SFT PN -EPDM [On/Off]   Indicates condition of P (park) or N (neutral) position from TCM on CAN communication line.
SFT P -MET [On/Off]   Indicates condition of P (park) position from TCM on CAN communication line.
SFT N -MET [On/Off]   Indicates condition of N (neutral) position from EPDM E/R on CAN communication line.
ENGINE STATE [Stop/Start/Crank/Run] * Indicates condition of engine state from ECM on CAN communication line.
VEH SPEED 1 [mph/km/h] * Indicates condition of vehicle speed signal received from ABS on CAN communication line.
VEH SPEED 2 [mph/km/h] * Indicates condition of vehicle speed signal received from combination meter on CAN communication line.
DOOR STAT-DR [LOCK/READY/UNLK] * Indicates condition of driver side door status.
DOOR STAT-AS [LOCK/READY/UNLK] * Indicates condition of passenger side door status.
ID OK FLAG [Set/Reset]   Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset]   Indicates condition of engine start possibility.
RKE OPE COUN1 [0-19] * When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19] * When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing.
TRNK/HAT MNTR [On/Off]   Indicates condition of trunk lid switch.
RKE-LOCK [On/Off]   Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off]   Indicates condition of unlock signal from Intelligent Key.
RKE-TR/BD [On/Off]   Indicates condition of trunk open signal from Intelligent Key.
RKE-PANIC [On/Off]   Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off]   Indicates condition of mode change signal from Intelligent Key.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.