2014 Nissan-Datsun NV3500 HD S, Van CargoFACTORY OEM SERVICE PROCEDURE

Work Procedure

  1. SAVE ECM DATA 

    With CONSULT

    1. Turn ignition switch OFF.
    2. Reconnect all harness connectors disconnected.
    3. Turn ignition switch ON.
    4. Select "SAVING DATA FOR REPLC CPU" in "WORK SUPPORT" mode of "ENGINE" using CONSULT.
    5. Follow the instruction of CONSULT display.
    NOTE:
    • Necessary data in ECM is copied and saved to CONSULT.
    • Go to Step 2 regardless of with or without success in saving data.

    :GO TO 2.

  2. CHECK ECM PART NUMBER 

    Check ECM part number to see whether it is blank ECM or not.

    NOTE:
    • Part number of blank ECM is 23703 - xxxxx.
    • Check part number when ordering ECM or the one included in the label on the container box.

    Is the ECM a blank ECM? 

    YES: GO TO 3.

    NO: GO TO  5.

  3. SAVE ECM PART NUMBER 

    Read out the part number from the old ECM and save the number, following the programming instructions. Refer to CONSULT Operation Manual.

    NOTE:
    • The ECM part number is saved in CONSULT.
    • Even when ECM part number is not saved in CONSULT, go to 4.

    :GO TO 4.

  4. PERFORM ECM PROGRAMMING 

    After replacing ECM, perform the ECM programming. Refer to CONSULT Operation Manual.

    NOTE:
    • Refer to "REMOVAL AND INSTALLATION " for replacement of ECM.
    • During programming, maintain the following conditions:
      • Ignition switch: ON
      • Electric load: OFF
      • Brake pedal: Not depressed
      • Battery voltage: 12 - 13.5 V (Be sure to check the value of battery voltage by selecting "BATTERY VOLT" in "Data monitor" of CONSULT.)

    :GO TO  6.

  5. REPLACE ECM 

    Replace ECM. Refer to "REMOVAL AND INSTALLATION ".

    :GO TO 6.

  6. PERFORM INITIALIZATION OF IVIS (NATS) SYSTEM AND REGISTRATION OF ALL IVIS (NATS) IGNITION KEY IDS 

    Refer to "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT: SPECIAL REPAIR REQUIREMENT ".

    :GO TO 7.

  7. CHECK ECM DATA STATUS 

    Check if the data is successfully copied from the ECM at Step  1 (before replacement) and saved in CONSULT.

    Is the data saved successfully? 

    YES: GO TO 8.

    NO: GO TO  9.

  8. WRITE ECM DATA 

    With CONSULT

    1. Select "WRITING DATA FOR REPLC CPU" in "WORK SUPPORT" mode of "ENGINE" using CONSULT.
    2. Follow the instruction of CONSULT display.
      NOTE: The data saved by "SAVING DATA FOR REPLC CPU" is written to ECM.

      :GO TO  10.

  9. PERFORM VIN REGISTRATION 

    Refer to "WORK PROCEDURE ".

    :GO TO 10.

  10. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING 

    Refer to "WORK PROCEDURE ".

    :GO TO 11.

  11. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING 

    Refer to "WORK PROCEDURE ".

    :GO TO 12.

  12. PERFORM IDLE AIR VOLUME LEARNING 

    Refer to "WORK PROCEDURE ".

    :END

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.