2013 Nissan-Datsun NV3500 HD S, Van CargoFACTORY OEM SERVICE PROCEDURE

Active Test Mode

Test Item

Test item Condition Judgment Check item (Remedy)
FUEL INJECTION
  • Engine: Return to the original non-standard condition
  • Change the amount of fuel injection using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Fuel injector
  • Air fuel ratio (A/F) sensor 1
ENG COOLANT TEMP
  • Engine: Return to the original non-standard condition
  • Change the engine coolant temperature using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Engine coolant temperature sensor
  • Fuel injector
PURG VOL CONT/V
  • Engine: After warming up, run engine at 1, 500 RPM.
  • Change the EVAP canister purge volume control solenoid valve opening percent using CONSULT.
 Engine speed changes according to the opening percent.
  • Harness and connectors
  • Solenoid valve
FUEL/T TEMP SEN
  • Change the fuel tank temperature using CONSULT.
FUEL PUMP RELAY
  • Ignition switch: ON (Engine stopped)
  • Turn the fuel pump relay "ON" and "OFF" using CONSULT and listen to operating sound.
 Fuel pump relay makes the operating sound.
  • Harness and connectors
  • Fuel pump relay
IGNITION TIMING
  • Engine: Return to the original non-standard condition
  • Timing light: Set
  • Retard the ignition timing using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Perform Idle Air Volume Learning.
POWER BALANCE
  • Engine: After warming up, idle the engine.
  • A/C switch OFF
  • Selector lever: P or N position
  • Cut off each injector signal one at a time using CONSULT.
 Engine runs rough or stops.
  • Harness and connectors
  • Compression
  • Fuel injector
  • Power transistor
  • Spark plug
  • Ignition coil
COOLING FAN()
  • Ignition switch: ON
  • Turn the cooling fan "HI", "LOW" and "OFF" using CONSULT.
 Cooling fan moves and stops.
  • Harness and connectors
  • Cooling fan motor
  • IPDM E/R
VENT CONTROL/V
  • Ignition switch: ON (Engine stopped)
  • Turn solenoid valve "ON" and "OFF" with the CONSULT and listen to operating sound.
 Solenoid valve makes an operating sound.
  • Harness and connectors
  • Solenoid valve
V/T ASSIGN ANGLE
  • Engine: Return to the original non-standard condition
  • Change intake valve timing using CONSULT.
 If malfunctioning symptom disappears, see CHECK ITEM.
  • Harness and connectors
  • Intake valve timing control solenoid valve
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.