Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Nissan-Datsun Cube BaseFACTORY OEM SERVICE PROCEDURE
Physical Values
| Terminal No. (Wire color) | Description | Condition | Value (Approx.) | |||
|---|---|---|---|---|---|---|
| + | - | Signal name | Input/Output | |||
| 2 (BR/W) | Ground | Combination switch INPUT 5 | Input | Combination switch (Wiper intermittent dial 4) | All switch OFF | 0 V |
| Turn signal switch RH |
1.0 V |
|||||
| Lighting switch HI | ||||||
| Lighting switch 1ST | ||||||
| Lighting switch 2ND |
2.0 V |
|||||
| 3 (GR) | Ground | Combination switch INPUT 4 | Input | Combination switch (Wiper intermittent dial 4) | All switch OFF | 0 V |
| Turn signal switch LH |
1.0 V |
|||||
| Lighting switch PASS | ||||||
| Lighting switch 2ND | ||||||
| Front fog lamp switch ON |
0.8 V |
|||||
| 4 (L/Y) | Ground | Combination switch INPUT 3 | Input | Combination switch (Wiper intermittent dial 4) | All switch OFF | 0 V |
| Front wiper switch LO |
1.0 V |
|||||
| Front wiper switch MIST | ||||||
| Front wiper switch INT | ||||||
| Lighting switch AUTO | ||||||
| 5 (G) | Ground | Combination switch INPUT 2 | Input | Combination switch | All switch OFF (Wiper intermittent dial 4) | 0 V |
| Front washer switch (Wiper intermittent dial 4) |
1.0 V |
|||||
| Rear washer ON (Wiper intermittent dial 4) | ||||||
Any of the condition below with all switch OFF
|
||||||
| Rear wiper switch ON (Wiper intermittent dial 4) |
0.8 V |
|||||
| 6 (L/R) | Ground | Combination switch INPUT 1 | Input | Combination switch | All switch OFF (Wiper intermittent dial 4) | 0 V |
| Front wiper switch HI (Wiper intermittent dial 4) |
1.0 V |
|||||
| Rear wiper switch INT (Wiper intermittent dial 4) | ||||||
| Wiper intermittent dial 3 (All switch OFF) | ||||||
Any of the condition below with all switch OFF
|
1.9 V |
|||||
Any of the condition below with all switch OFF
|
0.8 V |
|||||
| 7 (W/R) | Ground | Door key cylinder switch UNLOCK | Input | Door key cylinder switch | NEUTRAL position |
8.0 - 8.5 V |
| UNLOCK position | 0 V | |||||
| 8 (W/B) | Ground | Door key cylinder switch LOCK | Input | Door key cylinder switch | NEUTRAL position | 12 V |
| LOCK position | 0 V | |||||
| 9 (R) | Ground | Stop lamp switch 1 | Input | Stop lamp switch | OFF (Brake pedal is not depressed) | 0 V |
| ON (Brake pedal is depressed) | Battery voltage | |||||
| 12 (GR) | Ground | Door lock and unlock switch LOCK | Input | Door lock and unlock switch | NEUTRAL position |
1.0 - 1.5 V |
| LOCK position | 0 V | |||||
| 13 (BR) | Ground | Door lock and unlock switch UNLOCK | Input | Door lock and unlock switch | NEUTRAL position |
1.0 - 1.5 V |
| UNLOCK position | 0 V | |||||
| 14 (L/G) | Ground | Optical sensor | Input | Ignition switch ON | When bright outside of the vehicle | Close to 5 V |
| When dark outside of the vehicle | Close to 0 V | |||||
| 15 (W/L) | Ground | Rear window defogger switch | Input | Rear window defogger switch | Not pressed |
1.0 - 1.5 V |
| Pressed | 0 V | |||||
| 17 (R/G) | Ground | Optical sensor power supply | Output | Ignition switch | OFF, ACC | 0 V |
| ON | 5 V | |||||
| 18 (V) | Ground | Sensor ground | Input | Ignition switch ON | 0 V | |
| 21 (P/L) | Ground | NATS antenna amp. | Input/Output | Intelligent Key: Intelligent Key battery is removed | Brake pedal: Depressed
NOTE:
Waveform varies each time when brake pedal is depressed
|
12 V |
| Brake pedal: Not depressed | 12 V | |||||
| 23 (R/Y) | Ground | Security indicator lamp | Output | Security indicator | ON | 0 V |
| Blinking (Ignition switch OFF) |
12.0 V |
|||||
| OFF | Battery voltage | |||||
| 24(1) (SB) | Ground | Dongle link | Input/Output | Ignition switch OFF | 5 V | |
| 25 (LG) | Ground | NATS antenna amp. | Input/Output | During waiting | Brake pedal: Depressed
NOTE:
Waveform varies each time when brake pedal is depressed
|
12 V |
| Brake pedal: Not depressed | 12 V | |||||
| 26(2) (GR) | Ground | Thermo control amp. | Input | Ignition switch ON | 0 V | |
| Evaporator is extremely low temperature | 12 V | |||||
| 27 (O) | Ground | A/C ON (Automatic A/C) | Input | A/C | OFF (A/C switch indicator: OFF) |
1.0 - 1.5 V |
| ON (A/C switch indicator: ON) | 0 V | |||||
| A/C switch (Manual A/C) | A/C switch | OFF |
1.0 - 1.5 V |
|||
| ON | 0 V | |||||
| 28 (G/W) | Ground | Blower fan switch (Automatic A/C) | Input | Fan switch | Blower fan switch OFF | 0 V |
| Blower fan switch ON |
7.0 - 8.0 V |
|||||
| Blower fan switch (Manual A/C) | Fan switch | Blower fan switch OFF |
1.5 - 2.0 V |
|||
| Blower fan switch ON | 0 V | |||||
| 29 (L/W) | Ground | Hazard switch | Input | Hazard switch | OFF | 12 V |
| ON | 0 V | |||||
| 31 (G/B) | Ground | Front door lock assembly driver side (Unlock sensor) | Input | Driver door | LOCK status (Unlock sensor switch OFF) |
7.0 - 8.0 V |
| UNLOCK status (Unlock sensor switch ON) | 0 V | |||||
| 32 (LG) | Ground | Combination switch OUTPUT 5 | Output | Combination switch | All switch OFF (Wiper intermittent dial 4) |
7.0 - 8.0 V |
| Front fog lamp switch ON (Wiper intermittent dial 4) |
1.0 V |
|||||
| Rear wiper switch ON (Wiper intermittent dial 4) | ||||||
Any of the condition below with all switch OFF
|
||||||
| 33 (Y/L) | Ground | Combination switch OUTPUT 4 | Output | Combination switch | All switch OFF (Wiper intermittent dial 4) |
7.0 - 8.0 V |
| Lighting switch 1ST (Wiper intermittent dial 4) |
1.2 V |
|||||
| Lighting switch AUTO (Wiper intermittent dial 4) | ||||||
| Rear wiper switch INT (Wiper intermittent dial 4) | ||||||
Any of the condition below with all switch OFF
|
||||||
| 34 (W) | Ground | Combination switch OUTPUT 3 | Output | Combination switch | All switch OFF (Wiper intermittent dial 4) |
7.0 - 8.0 V |
| Lighting switch 2ND (Wiper intermittent dial 4) |
1.2 V |
|||||
| Lighting switch HI (Wiper intermittent dial 4) | ||||||
| Rear washer switch ON (Wiper intermittent dial 4) | ||||||
Any of the condition below with all switch OFF
|
||||||
| 35 (R/L) | Ground | Combination switch OUTPUT 2 | Output | Combination switch (Wiper intermittent dial 4) | All switch OFF |
7.0 - 8.0 V |
| Lighting switch 2ND |
1.2 V |
|||||
| Lighting switch PASS | ||||||
| Front wiper switch INT | ||||||
| Front wiper switch HI | ||||||
| 36 (L/O) | Ground | Combination switch OUTPUT 1 | Output | Combination switch (Wiper intermittent dial 4) | All switch OFF |
7.0 - 8.0 V |
| Turn signal switch RH |
1.2 V |
|||||
| Turn signal switch LH | ||||||
| Front wiper switch LO (Front wiper switch MIST) | ||||||
| Front washer switch ON | ||||||
| 37 (G/O) | Ground | Selector lever P position switch | Input | Selector lever | P position | 0 V |
| Any position other than P | 12 V | |||||
| 38 (G/Y) | Ground | Receiver communication | Input/Output | Ignition switch OFF (Remote keyless entry communication) | Waiting | 12 V |
| When operating either button on Intelligent Key | ||||||
| Ignition switch ON (TPMS communication) | Waiting | |||||
| When receiving signal from tire pressure sensor | ||||||
| 39 (L) | Ground | CAN-H | Input/Output | - | - | |
| 40 (P) | Ground | CAN-L | Input/Output | - | - | |
| 43 (W) | Ground | Back door switch | Input | Back door switch | OFF (When back door closed) |
9.5 - 10.0 V |
| ON (When back door opened) | 0 V | |||||
| 44 (LG) | Ground | Rear wiper stop position | Input | Ignition switch ON | Rear wiper stop position | 12 V |
| Any position other than rear wiper stop position | 0 V | |||||
| 45 (SB) | Ground | Passenger door switch | Input | Passenger door switch | OFF (When passenger door closed) |
7.0 - 8.0 V |
| ON (When passenger door opened) | 0 V | |||||
| 46 (GR/L) | Ground | Rear RH door switch | Input | Rear RH door switch | OFF (When rear RH door closed) |
7.0 - 8.0 V |
| ON (When rear RH door opened) | 0 V | |||||
| 47 (BR/Y) | Ground | Driver door switch | Input | Driver door switch | OFF (When driver door closed) |
7.0 - 8.0 V |
| ON (When driver door opened) | 0 V | |||||
| 48 (W/G) | Ground | Rear LH door switch | Input | Rear LH door switch | OFF (When rear LH door closed) |
7.0 - 8.0 V |
| ON (When rear door LH opened) | 0 V | |||||
| 50 (R/W) | Ground | Back door lock actuator relay control | Output | Back door | LOCK (Actuator is activated) | 0 V |
| Other than LOCK (Actuator is not activated) | Battery voltage | |||||
| 51 (W) | Ground | Back door request switch | Input | Back door request switch | ON (Pressed) | 0 V |
| OFF (Not pressed) | 12 V | |||||
| 54 (LG) | Ground | Rear wiper | Output | Rear wiper | OFF (Stopped) | 0 V |
| ON (Activated) | 12 V | |||||
| 55 (G) | Ground | Rear door UNLOCK | Output | Rear door | UNLOCK (Actuator is activated) | 12 V |
| Other then UNLOCK (Actuator is not activated) | 0 V | |||||
| 56 (L) | Ground | Interior room lamp power supply | Output | Interior room lamp battery saver is activated. (Cuts the interior room lamp power supply) | 0 V | |
| Interior room lamp battery saver is not activated. (Outputs the interior room lamp power supply) | 12 V | |||||
| 57 (Y) | Ground | Battery power supply | Input | Ignition switch OFF | Battery voltage | |
| 59 (G) | Ground | Passenger door UNLOCK | Output | Passenger door | UNLOCK (Actuator is activated) | 12 V |
| Other then UNLOCK (Actuator is not activated) | 0 V | |||||
| 60 (W/B) | Ground | Turn signal LH | Output | Ignition switch ON | Turn signal switch OFF | 0 V |
| Turn signal switch LH |
6.0 V |
|||||
| 61 (W/L) | Ground | Turn signal RH | Output | Ignition switch ON | Turn signal switch OFF | 0 V |
| Turn signal switch RH |
6.0 V |
|||||
| 63 (BR) | Ground | Interior room lamp control signal | Output | Interior room lamp | OFF | 12 V |
| ON | 0 V | |||||
| 65 (V) | Ground | All doors LOCK | Output | All doors | LOCK (Actuator is activated) | 12 V |
| Other then LOCK (Actuator is not activated) | 0 V | |||||
| 66 (L/B) | Ground | Driver door UNLOCK | Output | Driver door | UNLOCK (Actuator is activated) | 12 V |
| Other then UNLOCK (Actuator is not activated) | 0 V | |||||
| 67 (B) | Ground | Ground | Output | Ignition switch ON | 0 V | |
| 68 (L) | Ground | P/W power supply (IGN) | Output | Ignition switch ON | 12 V | |
| 69 (P) | Ground | P/W power supply (BAT) | Output | Ignition switch OFF | 12 V | |
| 70 (Y) | Ground | Battery power supply | Input | Ignition switch OFF | Battery voltage | |
| 72(2) (SB) | Ground | A/C indicator | Output | A/C indicator | OFF | 12 V |
| ON | 0 V | |||||
| 75 (SB) | Ground | Driver door request switch | Input | Driver door request switch | ON (Pressed) | 0 V |
| OFF (Not pressed) | 12 V | |||||
| 76 (L/O) | Ground | Push-button ignition switch (push switch) | Input | Push-button ignition switch (push switch) | Pressed | 0 V |
| Not pressed | 12 V | |||||
| 78 (LG) | Ground | Driver door antenna (+) | Output | When the driver door request switch is operated with ignition switch ON | When Intelligent Key is not in the antenna detection area (The distance between Intelligent Key and antenna: Approx. 2 m) | |
| When Intelligent Key is in the antenna detection area (The distance between Intelligent Key and antenna: 80 cm or less) | ||||||
| 79 (V) | Ground | Driver door antenna (-) | Output | When the driver door request switch is operated with ignition switch ON | When Intelligent Key is not in the antenna detection area (The distance between Intelligent Key and antenna: Approx. 2 m) | |
| When Intelligent Key is in the antenna detection area (The distance between Intelligent Key and antenna: 80 cm or less) | ||||||
| 80 (BR/Y) | Ground | Passenger door antenna (+) | Output | When the passenger door request switch is operated with ignition switch ON | When Intelligent Key is not in the antenna detection area (The distance between Intelligent Key and antenna: Approx. 2 m) | |
| When Intelligent Key is in the antenna detection area (The distance between Intelligent Key and antenna: 80 cm or less) | ||||||
| 81 (L/Y) | Ground | Passenger door antenna (-) | Output | When the passenger door request switch is operated with ignition switch ON | When Intelligent Key is not in the antenna detection area (The distance between Intelligent Key and antenna: Approx. 2 m) | |
| When Intelligent Key is in the antenna detection area (The distance between Intelligent Key and antenna: 80 cm or less) | ||||||
| 82 (W/B) | Ground | Back door antenna (+) | Output | When the back door request switch is operated with ignition switch ON | When Intelligent Key is not in the antenna detection area (The distance between Intelligent Key and antenna: Approx. 2 m) | |
| When Intelligent Key is in the antenna detection area (The distance between Intelligent Key and antenna: 80 cm or less) | ||||||
| 83 (B/W) | Ground | Back door antenna (-) | Output | When the back door request switch is operated with ignition switch ON | When Intelligent Key is not in the antenna detection area (The distance between Intelligent Key and antenna: Approx. 2 m) | |
| When Intelligent Key is in the antenna detection area (The distance between Intelligent Key and antenna: 80 cm or less) | ||||||
| 84 (Y/G) | Ground | Room antenna (+) (Instrument center) | Output | Ignition switch ON | When Intelligent Key is not in the antenna detection area | |
| When Intelligent Key is in the antenna detection area | ||||||
| 85 (Y/L) | Ground | Room antenna (-) (Instrument center) | Output | Ignition switch ON | When Intelligent Key is not in the antenna detection area | |
| When Intelligent Key is in the antenna detection area | ||||||
| 86 (P) | Ground | Luggage room antenna (+) | Output | Ignition switch ON | When Intelligent Key is not in the antenna detection area | |
| When Intelligent Key is in the antenna detection area | ||||||
| 87 (L) | Ground | Luggage room antenna (-) | Output | Ignition switch ON | When Intelligent Key is not in the antenna detection area | |
| When Intelligent Key is in the antenna detection area | ||||||
| 90 (W/L) | Ground | Push-button ignition switch illumination | Output | Push-button ignition switch illumination | ON | 12 V |
| OFF | 0 V | |||||
| 91 (Y) | Ground | ACC/ON indicator lamp | Output | Ignition switch | OFF | Battery voltage |
| ACC or ON | 0.5 V | |||||
| 92 (BR/R) | Ground | Push-button ignition switch illumination ground | Output | Tail lamp | OFF | 0 V |
| ON |
NOTE:
When the illumination brightening/dimming level is in the neutral position Factory Service Tools Use the Manual With the Right HardwarePair factory procedures with proven DIY tools so the instructions are easier to execute. Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you. When to See a MechanicStop DIY work and contact a certified mechanic immediately if any of the following apply:
| |||||
