Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Nissan-Datsun Leaf SLFACTORY OEM SERVICE PROCEDURE
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)
WORK SUPPORT
WORK SUPPORT CHART
| Monitor item | Description |
|---|---|
| INSIDE ANT DIAGNOSIS | This function allows inside key antenna self-diagnosis |
| LOCK/UNLOCK BY I-KEY | Door lock/unlock function by door request switch mode can be changed to operation in this mode
|
| ENGINE START BY I-KEY | READY set function mode can be changed to operation with this mode
|
| TRUNK/GLASS HATCH OPEN |
NOTE:
This item is displayed, but cannot be used
|
| HORN WITH KEYLESS LOCK | Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not operate (OFF) with this mode
|
| PANIC ALARM SET | Panic alarm button pressing time on Intelligent Key remote control button can be selected from the following with this mode
|
| TRUNK OPEN DELAY |
NOTE:
This item is displayed, but cannot be used
|
| LO-BATT OF KEY FOB WARN | Intelligent Key low battery warning mode can be changed to operation with this mode
|
| ANTI KEY LOCK IN FUNCTI | Key reminder function mode can be changed to operation with this mode
|
| HAZARD ANSWER BACK | Hazard reminder function mode by door request switch and Intelligent Key button can be selected from the following with this mode
|
| ANS BACK I-KEY LOCK | Buzzer reminder function (lock operation) mode by door request switch can be selected from the following with this mode
|
| ANS BACK I-KEY UNLOCK | Buzzer reminder function (unlock operation) mode by door request switch can be changed to operation with this mode
|
| SHORT CRANKING OUTPUT |
NOTE:
This item is displayed, but cannot be used
|
| CONFIRM KEY FOB ID | It can be checked whether Intelligent Key ID code is registered or not in this mode |
| AUTO LOCK SET | Auto door lock operation time can be changed in this mode
|
SELF-DIAG RESULT
Refer to "DTC INDEX ".
DATA MONITOR
DATA MONITOR REFERENCE CHART
| Monitor Item | Condition | ||
|---|---|---|---|
| REQ SW-DR | Indicates [On/Off] condition of door request switch (driver side) | ||
| REQ SW-AS | Indicates [On/Off] condition of door request switch (passenger side) | ||
| REQ SW-BD/TR | Indicates [On/Off] condition of back door request switch | ||
| PUSH SW | Indicates [On/Off] condition of power switch | ||
| CLUTCH SW |
NOTE:
This item is displayed, but cannot be monitored
|
||
| BRAKE SW 1 | Indicates [On/Off](1) condition of stop lamp switch power supply | ||
| BRAKE SW 2 | Indicates [On/Off] condition of stop lamp switch | ||
| DETE/CANCL SW | Indicates [On/Off] condition of P position | ||
| SFT PN/N SW | Indicates [On/Off] condition of P or N position | ||
| UNLK SEN-DR | Indicates [On/Off] condition of driver door UNLOCK status | ||
| PUSH SW-IPDM | Indicates [On/Off] condition of power switch | ||
| IGN RLY1-F/B | Indicates [On/Off] condition of ignition relay 1 | ||
| DETE SW-IPDM | Indicates [On/Off] condition of P position | ||
| SFT PN-IPDM |
NOTE:
This item is displayed, but cannot be monitored
|
||
| SFT P-MET | Indicates [On/Off] condition of P position | ||
| SFT N-MET | Indicates [On/Off] condition of N position | ||
| ENGINE STATE |
NOTE:
This item is displayed, but cannot be monitored
|
||
| S/L LOCK-IPDM |
NOTE:
This item is displayed, but cannot be monitored
|
||
| S/L UNLK-IPDM |
NOTE:
This item is displayed, but cannot be monitored
|
||
| S/L RELAY-REQ |
NOTE:
This item is displayed, but cannot be monitored
|
||
| VEH SPEED 1 | Display the vehicle speed signal received from combination meter by numerical value [km/h] | ||
| VEH SPEED 2 | Display the vehicle speed signal received from ABS actuator and electric unit (control unit) by numerical value [km/h] | ||
| DOOR STAT-DR | Indicates [LOCK/READY/UNLK] condition of driver side door status | ||
| DOOR STAT-AS | Indicates [LOCK/READY/UNLK] condition of passenger side door status | ||
| ID OK FLAG | Indicates [Set/Reset] condition of key ID | ||
| PRMT ENG STRT | Indicates [Set/Reset] condition of ENGINE START BY I-KEY setting in WORK SUPPORT mode | ||
| PRMT RKE STRT |
NOTE:
This item is displayed, but cannot be monitored
|
||
| TRNK/HAT MNTR |
NOTE:
This item is displayed, but cannot be monitored
|
||
| RKE-LOCK | Indicates [On/Off] condition of LOCK signal from Intelligent Key | ||
| RKE-UNLOCK | Indicates [On/Off] condition of UNLOCK signal from Intelligent Key | ||
| RKE-TR/BD |
NOTE:
This item is displayed, but cannot be monitored
|
||
| RKE-PANIC | Indicates [On/Off] condition of PANIC button of Intelligent Key | ||
| RKE-MODE CHG | Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key | ||
| RKE OPE COUN1 | When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing | ||
| RKE OPE COUN2 |
NOTE:
This item is displayed, but cannot be monitored
|
||
|
|||
ACTIVE TEST
ACTIVE TEST REFERENCE CHART
| Test item | Description |
|---|---|
| OUTSIDE BUZZER | This test is able to check Intelligent Key warning buzzer operation
|
| INSIDE BUZZER | This test is able to check warning chime in combination meter operation
|
| INDICATOR | This test is able to check warning lamp operation
|
| INT LAMP | This test is able to check interior room lamp operation
|
| LCD | This test is able to check meter display information
|
| FLASHER | This test is able to check security hazard lamp operation The hazard lamps are activated after "LH/RH/Off" on CONSULT screen is touched |
| HORN | This test is able to check horn operation
|
| P RANGE | This test is able to check P position signal from electric shift control unit
|
| ENGINE SW ILLUMI | This test is able to check power switch illumination operation Power switch illumination illuminates when "ON" on CONSULT screen is touched |
| PUSH SWITCH INDICATOR | This test is able to check LOCK indicator in power switch operation LOCK indicator in power switch illuminates when "ON" on CONSULT screen is touched |
| BATTERY SAVER | This test is able to check interior room lamp operation. The interior room lamp will be activated after "ON" on CONSULT screen is touched. |
| TRUNK/BACK DOOR | This test is able to check back door opener actuator open operation. This actuator opens when "Open" on CONSULT screen is touched. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.