2008 Nissan-Datsun Sentra SE-RFACTORY OEM SERVICE PROCEDURE

Diagnostic Procedure

WARNING: This page is about a different car, the 2007 Nissan Pathfinder. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK OVERALL FUNCTION 
    1. Turn ignition switch ON.
    2. Pinch fuel feed hose with two fingers.

      Fuel pressure pulsation should be felt on the fuel feed hose for 1 second after ignition switch is turned ON  .

      Fig 1: Identifying Oil Filler Cap And Fuel Feed Hose
      G04897406Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: INSPECTION END 

    NG: GO TO 2.

  2. CHECK FUEL PUMP POWER SUPPLY CIRCUIT-I 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Turn ignition switch ON.
    4. Check voltage between ECM terminal 113 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

      Fig 2: Check Voltage Between ECM Terminal 113 And Ground
      G04900786Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO  5.

    NG: GO TO 3.

  3. CHECK FUEL PUMP POWER SUPPLY CIRCUIT-II 

    Check voltage between IPDM E/R terminal 46 and ground with CONSULT-II or tester.

    Voltage: Battery voltage 

    Fig 3: Checking Voltage Between IPDM E/R Terminal 46 And Ground
    G04900787Courtesy of NISSAN NORTH AMERICA, INC.

    OK or NG 

    OK: GO TO 4.

    NG: GO TO  12.

  4. DETECT MALFUNCTIONING PART 

    Check harness for open or short between IPDM E/R and ECM

    Repair harness or connectors.

  5. CHECK FUEL PUMP POWER SUPPLY CIRCUIT-III 
    1. Turn ignition switch OFF.
    2. Reconnect all harness connectors disconnected.
    3. Disconnect "fuel level sensor unit and fuel pump" harness connector.
      Fig 4: Identifying Fuel Level Sensor Unit And Fuel Pump Harness Connector
      G04894781Courtesy of NISSAN NORTH AMERICA, INC.
    4. Turn ignition switch ON.
    5. Check voltage between "fuel level sensor unit and fuel pump" terminal 1 and ground with CONSULT-II or tester.

      Voltage: Battery voltage should exist for 1 second after ignition switch is turned ON  .

      Fig 5: Checking Voltage Between Fuel Level Sensor Unit And Fuel Pump Terminal 1 And Ground
      G04895195Courtesy of NISSAN NORTH AMERICA, INC.
    6. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO  9.

    NG: GO TO 6.

  6. CHECK 15A FUSE 
    1. Turn ignition switch OFF.
    2. Disconnect 15A fuse.
    3. Check 15A fuse.

    OK or NG 

    OK: GO TO 7.

    NG: Replace fuse.

  7. CHECK FUEL PUMP POWER SUPPLY CURCUIT-IV 
    1. Disconnect IPDM E/R harness connector E119.
    2. Check harness continuity between "fuel level sensor unit and fuel pump" terminal 1 and IPDM E/R terminal 13.

      Refer to Wiring Diagram .

      Continuity should exist  .

    3. Also check harness for short to ground and short to power.

    OK or NG 

    OK: GO TO  12.

    NG: GO TO 8.

  8. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors C1, E41
    • Harness for open or short between "fuel level sensor unit and fuel pump" and IPDM E/R

    Repair open circuit or short to ground or short to power in harness or connectors.

  9. CHECK FUEL PUMP GROUND CIRCUIT FOR OPEN AND SHORT 
    1. Check harness continuity between "fuel level sensor unit and fuel pump" terminal 3 and ground.

      Refer to Wiring Diagram .

      Continuity should exist  .

    2. Also check harness for short to ground.

    OK or NG 

    OK: GO TO  11.

    NG: GO TO 10.

  10. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors C1, E41
    • Harness for open or short between "fuel level sensor unit and fuel pump" and ground

    Repair open circuit or short to power in harness or connectors.

  11. CHECK FUEL PUMP 

    Refer to "COMPONENT INSPECTION ".

    OK or NG 

    OK: GO TO 12.

    NG: Replace fuel pump.

  12. CHECK INTERMITTENT INCIDENT 

    Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

    OK or NG 

    OK: Replace IPDM E/R.

    NG: Repair or replace harness or connectors.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.