Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Fuel Level Sensor Signal Inspection
Symptom:
- Improper fuel gauge indication.
- Low-fuel warning lamp indication is irregular.
- Depending on vehicle position or driving circumstance, the fuel level in the tank shifts and the indication may fluctuate.
- If the vehicle is fueled with the ignition switch ON, the indication will update slowly.
- If the vehicle is tilted when the ignition switch is turned ON, fuel in the tank may flow to one direction resulting in a change of reading.
- CHECK COMBINATION METER INPUT SIGNALÂ
- Select "METER/M&A" on CONSULT-III.
- Using "FUEL METER" on "DATA MONITOR", compare the value of "DATA MONITOR" with fuel gauge indication of combination meter.REFERENCE VALUE OF DATA MONITOR
Fuel gauge indication (approx. segments) Reference value of data monitor [lit.] Full (13) Approx. 55 3/4 (10) Approx. 38 1/2 (7) Approx. 25 1/4 (4) Approx. 13 Empty (0) Approx. 4
OK or NGÂ
OK: GO TO 2.
NG: Replace combination meter. Refer to "COMBINATION METER ".
- CHECK HARNESS CONNECTORÂ
- Turn ignition switch OFF.
- Check combination meter and fuel level sensor unit terminals (meter-side and harness-side) for poor connection.
OK or NGÂ
OK: GO TO 3.
NG: Repair or replace terminals or connectors.
- CHECK FUEL LEVEL SENSOR UNIT CIRCUITÂ
- Disconnect combination meter connector and fuel level sensor unit connector.
- Check continuity between combination meter harness connector (A) and fuel level sensor unit and fuel pump harness connector (B).CONNECTOR TERMINAL CONTINUITY SPECIFICATION
A B Continuity Connector Terminal Connector Terminal M24 8 B48 2 Yes - Check continuity between combination meter harness connector (A) and ground.CONNECTOR TERMINAL CONTINUITY SPECIFICATION
A Ground Continuity Connector Terminal M24 8 No
OK or NGÂ
OK: GO TO 4.
NG: Repair harness or connector.
- CHECK FUEL LEVEL SENSOR UNIT GROUND CIRCUITÂ
- Check continuity between combination meter harness connector (A) and fuel level sensor unit and fuel pump harness connector (B).CONNECTOR TERMINAL CONTINUITY SPECIFICATION
A B Continuity Connector Terminal Connector Terminal M24 4 B48 5 Yes - Check continuity between combination meter harness connector (A) and ground.CONNECTOR TERMINAL CONTINUITY SPECIFICATION
A Ground Continuity Connector Terminal M24 4 No
OK or NGÂ
OK: GO TO 5.
NG: Repair harness or connector.
- Check continuity between combination meter harness connector (A) and fuel level sensor unit and fuel pump harness connector (B).
- CHECK FUEL LEVEL SENSOR UNITÂ
Check fuel level sensor unit. Refer to "FUEL LEVEL SENSOR UNIT CHECKÂ ".
OK or NGÂ
OK: Check fuel level sensor unit installation, and check whether the float arm interferes or binds with any of the internal components in the fuel tank. Repair or replace malfunctioning part, if necessary.
NG: Replace fuel level sensor unit.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
