Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- CHECK OVERALL FUNCTIONÂ
With CONSULT-IIÂ
- Start engine and warm it up to normal operating temperature.
- Perform "VIAS SOL VALVE" in "ACTIVE TEST" mode with CONSULT-II.
- Turn VIAS control solenoid valve "ON" and "OFF", and make sure that power valve actuator rod moves.
Without CONSULT-IIÂ
- Start engine and warm it up to normal operating temperature.
- Rev engine up to 3, 600 rpm and make sure that power valve actuator rod (2) moves.
- Power valve actuator (1)
OK or NGÂ
OK : INSPECTION ENDÂ
NG (With CONSULT-II) : GO TO 2.
NG (Without CONSULT-II) : GO TO Â 3.
- CHECK VACUUM EXISTENCEÂ
With CONSULT-IIÂ
- Stop engine and disconnect vacuum hose connected to power valve actuator.
- Install the vacuum gauge as shown in the figure.
- Start engine and let it idle.
- Perform "VIAS SOL VALVE" in "ACTIVE TEST" mode with CONSULT-II.
- Turn VIAS control solenoid valve ON and OFF, and check vacuum existence under the following conditions.Fig 3: Identifying Power Valve Actuator, VIAS Control Solenoid Valve & Vacuum Gauge (With CONSULT-II)
Courtesy of NISSAN MOTOR CO., U.S.A.
VACUUM DESCRIPTIONVIAS SOL VALVE Vacuum ON Should exist OFF Should not exist
OK or NGÂ
OK : Repair or replace power valve actuator.
NG : GO TO Â 4.
- CHECK VACUUM EXISTENCEÂ
Without CONSULT-IIÂ
- Stop engine and disconnect vacuum hose connected to power valve actuator.
- Install the vacuum gauge as shown in the figure.
- Disconnect VIAS control solenoid valve harness connector.
- Start engine and let it idle.
- Apply 12V of direct current between VIAS control solenoid valve terminals 1 and 2.
- Check vacuum existence under the following conditions.VACUUM CONDITIONS
Condition Vacuum 12V direct current supply Should exist No supply Should not exist
OK or NGÂ
OK : Repair or replace power valve actuator.
NG : GO TO 4.
- CHECK VACUUM HOSEÂ
- Stop engine.
- Check hoses and tubes between intake manifold and power valve actuator for crack, clogging, improper connection or disconnection. Refer to , "VACUUM HOSE DRAWING ".
OK or NGÂ
OK : GO TO 5.
NG : Repair hoses or tubes.
- CHECK VACUUM TANKÂ
Refer to , "COMPONENT INSPECTIONÂ ".
OK or NGÂ
OK : GO TO 6.
NG : Replace vacuum tank.
- CHECK VIAS CONTROL SOLENOID VALVE POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect VIAS control solenoid valve (2) harness connector.
- Power valve actuator (1)
- Turn ignition switch ON.
- Check voltage between terminal 1 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
OK : GO TO Â 8.
NG : GO TO 7.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E20, F32
- IPDM E/R connector E122
- 10A fuse
- Harness for open or short between VIAS control solenoid valve and fuse
: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK VIAS CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 29 and VIAS control solenoid valve terminal 2.
Refer to WIRING DIAGRAMÂ .
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
OK : GO TO 9.
NG : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK VIAS CONTROL SOLENOID VALVEÂ
Refer to , "COMPONENT INSPECTIONÂ ".
OK or NGÂ
OK : GO TO 10.
NG : Replace VIAS control solenoid valve.
- CHECK INTERMITTENT INCIDENTÂ
Refer to , "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".
: INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
