Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- INSPECTION STARTÂ
Turn ignition switch to START.
Is any cylinder ignited?Â
Yes or NoÂ
Yes (With CONSULT-II) : GO TO 2.
Yes (Without CONSULT-II) : GO TO Â 3.
No : GO TO Â 7.
- CHECK OVERALL FUNCTIONÂ
With CONSULT-IIÂ
- Start engine.
- Perform "POWER BALANCE" in "ACTIVE TEST" mode with CONSULT-II.
- Make sure that each circuit produces a momentary engine speed drop.
OK or NGÂ
OK : INSPECTION ENDÂ
NG : GO TO Â 7.
- CHECK FUNCTION OF FUEL INJECTOR-IÂ
Without CONSULT-IIÂ
- Stop engine.
- Disconnect harness connector F44 (1), F101 (2).
- <==: Vehicle front
- Intake manifold collector (3)
- Turn ignition switch ON.
- Check voltage between harness connector F44 terminal 6 (with triple meters) or 5 (without triple meters) and ground with CONSULT-II or tester.
Courtesy of NISSAN MOTOR CO., U.S.A.
Voltage: Battery voltageÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between harness connector F44 and ECM as follows.
Refer to WIRING DIAGRAMÂ .
With triple metersÂ
CONTINUITY REFERENCECylinder Harness connector F44 terminal ECM terminal 1 1 23 3 3 22 5 7 21 Without triple metersÂ
CONTINUITY REFERENCECylinder Harness connector F44 terminal ECM terminal 1 6 23 3 2 22 5 1 21 Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
OK : GO TO Â 5.
NG : GO TO 4.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors M71, F59
- Fuse block (J/B) connector M4
- 10A fuse
- Harness for open or short between harness connector F44 and fuse
- Harness for open or short between harness connector F44 and ECM
: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK FUNCTION OF FUEL INJECTOR-IIÂ
Provide battery voltage between harness connector F101 as follows and then interrupt it. Listen to each fuel injector operating sound.
With triple metersÂ
CYLINDER & TERMINALS SPECIFICATIONCylinder Harness connector F101 terminal (+) (-) 1 6 1 3 6 3 5 6 7 Without triple metersÂ
CYLINDER & TERMINALS SPECIFICATIONCylinder Harness connector F101 terminal (+) (-) 1 5 6 3 5 2 5 5 1 Operating sound should exist.Â
OK or NGÂ
OK : GO TO 6.
NG : GO TO Â 7.
- CHECK FUNCTION OF FUEL INJECTOR-IIIÂ
- Reconnect all harness connector disconnected.
- Start engine.
- Listen to fuel injectors No. 2, No. 4, No. 6 operating sound.
Clicking noise should exist.Â
OK or NGÂ
OK : INSPECTION ENDÂ
NG : GO TO 7.
- CHECK FUEL INJECTOR POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect fuel injector harness connector.
- Turn ignition switch ON.
- Check voltage between fuel injector terminal 1 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
OK : GO TO Â 9.
NG : GO TO 8.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors M71, F59
- Harness connectors F44, F101
- Fuse block (J/B) connector M4
- 10A fuse
- Harness for open or short between fuel injector and fuse
: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK FUEL INJECTOR OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between fuel injector terminal 2 and ECM terminals 21, 22, 23, 40, 41, 42.
Refer to WIRING DIAGRAMÂ .
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
OK : GO TO Â 11.
NG : GO TO 10.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors F101, F44
- Harness for open or short between fuel injector and ECM
: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK FUEL INJECTORÂ
Refer to , "COMPONENT INSPECTIONÂ ".
OK or NGÂ
OK : GO TO 12.
NG : Replace fuel injector.
- CHECK INTERMITTENT INCIDENTÂ
Refer to , "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".
: INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
