Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- INSPECTION STARTÂ
Do you have CONSULT-II?
Yes or NoÂ
- Yes : GO TO 2.
- No : GO TO Â 3.
- CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-1Â
With CONSULT-IIÂ
- Turn ignition switch ON.
- Check "LOAD SIGNAL" in "DATA MONITOR" mode with CONSULT-II under the following conditions.LIGHTING SWITCH CONDITIONS AND LOAD SIGNAL REFERENCE
Condition LOAD SIGNAL Lighting switch: ON at 2nd position ON Lighting switch: OFF OFF
OK or NGÂ
- CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-1Â
Without CONSULT-IIÂ
- Turn ignition switch ON.
- Check voltage between ECM terminal 84 and ground under the following conditions.
Courtesy of NISSAN MOTOR CO., U.S.A.
LIGHTING SWITCH CONDITIONS AND VOLTAGE REFERENCECondition Voltage Lighting switch: ON at 2nd position BATTERY VOLTAGE Lighting switch: OFF 0V
OK or NGÂ
- CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-2Â
With CONSULT-IIÂ
- Turn ignition switch ON.
- Check "LOAD SIGNAL" in "DATA MONITOR" mode with CONSULT-II under the following conditions.FAN CONTROL SWITCH CONDITIONS AND LOAD SIGNAL REFERENCE
Condition LOAD SIGNAL FAN control switch: ON in any position ON FAN control switch: OFF OFF
OK or NGÂ
- CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-2Â
Without CONSULT-IIÂ
- Turn ignition switch ON.
- Check voltage between ECM terminal 96 and ground under the following conditions.
Courtesy of NISSAN MOTOR CO., U.S.A.
FAN CONTROL SWITCH CONDITIONS AND VOLTAGE REFERENCECondition Voltage FAN control switch: ON in any position Approximately 0V FAN control switch: OFF Approximately 5V
OK or NGÂ
- CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-3Â
With CONSULT-IIÂ
- Turn ignition switch ON.
- Check "LOAD SIGNAL" in "DATA MONITOR" mode with CONSULT-II under the following conditions.REAR WINDOW DEFOGGER SWITCH CONDITIONS AND LOAD SIGNAL REFERENCE
Condition LOAD SIGNAL Rear window defogger switch: ON ON Rear window defogger switch: OFF OFF
OK or NGÂ
- OK : INSPECTION END.
- NG : GO TO Â 16.
- CHECK LOAD SIGNAL CIRCUIT OVERALL FUNCTION-3Â
Without CONSULT-IIÂ
- Turn ignition switch ON.
- Check voltage between ECM terminal 93 and ground under the following conditions.
Courtesy of NISSAN MOTOR CO., U.S.A.
REAR WINDOW DEFOGGER SWITCH CONDITIONS AND VOLTAGE REFERENCECondition Voltage Rear window defogger switch: ON BATTERY VOLTAGE Rear window defogger switch: OFF Approximately 0V
OK or NGÂ
- OK : INSPECTION END.
- NG : GO TO Â 16.
- CHECK HEADLAMP FUNCTIONÂ
- Start engine.
- Turn the lighting switch ON at 2nd position.
- Check that headlamps are illuminated.
OK or NGÂ
- OK (Models for USA) : GO TO 9.
- OK (Models for Canada) : GO TO Â 11.
- NG : Refer to HEADLAMP (FOR USA) or HEADLAMP (FOR CANADA) DAYTIME LIGHT SYSTEM-->.
- CHECK HEADLAMP INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Stop engine and turn ignition switch OFF.
- Disconnect ECM harness connector.
- Disconnect lighting switch harness connectors.
- Check harness continuity between ECM terminal 84 and lighting switch terminal 9, 10 under the following conditions.
Courtesy of NISSAN MOTOR CO., U.S.A.
ECM TERMINAL 84 AND LIGHTING SWITCH TERMINAL 9, 10: CONDITIONS AND CONTINUITY REFERENCECondition Continuity 1 Should exist 2 Should not exist - Also check harness for short to ground and short to power.
OK or NGÂ
- OK : GO TO Â 19.
- NG : GO TO 10.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E108, M19
- Harness connectors M58, F26
- Diode M55
- Harness for open and short between ECM and lighting switch
- : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK HEADLAMP INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Stop engine and turn ignition switch OFF.
- Disconnect ECM harness connector.
- Disconnect lighting switch harness connector E115
Disconnect daytime light control unit harness connector.
- Check harness continuity between ECM terminal 84 and lighting switch terminal 10, daytime light control unit terminal 6 under the following conditions.Fig 8: Checking Harness Continuity Between ECM Terminal 84 And Lighting Switch Terminal 10, Daytime Light Control Unit Terminal 6
Courtesy of NISSAN MOTOR CO., U.S.A.
ECM TERMINAL 84 AND LIGHTING SWITCH TERMINAL 10, DAYTIME LIGHT CONTROL UNIT TERMINAL 6: CONDITIONS AND CONTINUITY REFERENCECondition Continuity 1 Should exist 2 Should not exist - Also check harness for short to ground and short to power.
OK or NGÂ
- OK : GO TO Â 19.
- NG : GO TO 12.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E108, M19
- Harness connectors M58, F26
- Diode M55
- Harness for open and short between ECM and lighting switch
- Harness for open and short between ECM and daytime light control unit
- Harness for open and short between daytime light control unit and lighting switch
- : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK HEATER FAN SWITCH FUNCTIONÂ
- Turn the fan control switch ON in any position.
- Check that heater fan turns properly.
OK or NGÂ
- OK : GO TO 14.
- NG : Refer to TROUBLE DIAGNOSIS .
- CHECK HEATER FAN INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Disconnect air control harness connector.
- Check harness continuity between ECM terminal 96 and air control terminal 8, fan control switch terminal 6
Refer to WIRING DIAGRAMÂ .
- Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK : GO TO Â 19.
- NG : GO TO 15.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors M59, F27
- Harness for open or short between ECM and air control.
- Harness for open or short between ECM and fan control switch.
- : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK REAR WINDOW DEFOGGER FUNCTIONÂ
- Turn ignition switch OFF.
- Turn ON the rear window defogger switch.
- Check the rear windshield. Is the rear windshield and door mirror (with heated mirror models) heated up?
Yes or NoÂ
- Yes : GO TO 17.
- No : Refer to REAR WINDOW DEFOGGER .
- CHECK REAR WINDOW DEFOGGER INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Disconnect ECM harness connector.
- Disconnect rear window defogger relay.
- Check harness continuity between ECM terminal 93 and rear window defogger relay terminals 5, 7. Refer to WIRING DIAGRAMÂ
- Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK : GO TO Â 19.
- NG : GO TO 18.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors B1, M14
- Harness connectors M58, F26
- Harness for open or short between ECM and rear window defogger relay.
- : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK INTERMITTENT INCIDENTÂ
Perform "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".
- : INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
