Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- CHECK OVERALL FUNCTION-IÂ
With CONSULT-IIÂ
- Turn ignition switch ON.
- Select "BRAKE SW1" in "DATA MONITOR" mode with CONSULT-II.
- Check "BRAKE SW1" indication under the following conditions.
A/T modelsÂ
BRAKE SWITCH 1 INDICATION CONDITIONS - A/T MODELSCONDITION INDICATION When brake pedal is depressed OFF When brake pedal is fully released ON M/T modelsÂ
BRAKE SWITCH 1 INDICATION CONDITIONS - M/T MODELSCONDITION INDICATION When clutch pedal or brake pedal is depressed OFF When clutch pedal and brake pedal are fully released ON Without CONSULT-IIÂ
- Turn ignition switch ON.
- Check voltage between ECM terminal 108 and ground under the following conditions.
Courtesy of NISSAN MOTOR CO., U.S.A.
A/T modelsÂ
ECM TERMINAL 108 VOLTAGE CONDITIONS - A/T MODELSCONDITION VOLTAGE When brake pedal is depressed Approximately 0V When brake pedal is fully released Battery voltage M/T modelsÂ
ECM TERMINAL 108 VOLTAGE CONDITIONS - M/T MODELSCONDITION VOLTAGE When clutch pedal or brake pedal is depressed Approximately 0V When clutch pedal and brake pedal are fully released Battery voltage
OK or NGÂ
- CHECK OVERALL FUNCTION-IIÂ
With CONSULT-IIÂ
Check "BRAKE SW2" indication in "DATA MONITOR" mode.
BRAKE SWITCH 2 INDICATION CONDITIONS (CONSULT-II)CONDITION INDICATION When brake pedal is released OFF When brake pedal is depressed ON Without CONSULT-IIÂ
Check voltage between ECM terminal 101 and ground under the following conditions.
Courtesy of NISSAN MOTOR CO., U.S.A.
ECM CONNECTOR TERMINAL 101 VOLTAGE CONDITIONSCONDITION VOLTAGE When brake pedal is released Approximately 0V When brake pedal is depressed Battery voltage OK or NGÂ
- OK : INSPECTION ENDÂ
- NG : GO TO Â 13.
- CHECK ASCD CLUTCH SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect ASCD clutch switch harness connector.
- Turn ignition switch ON.
- Check voltage between ASCD clutch switch terminal 1 and ground under the following conditions with CONSULT-II or tester.
ASCD CLUTCH SWITCH TERMINAL 1 TERMINAL VOLTAGECONDITION VOLTAGE When brake pedal is released Battery voltage When brake pedal is depressed Approx. 0V OK or NGÂ
- OK : GO TO Â 10.
- NG : GO TO 4.
- CHECK ASCD BRAKE SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect ASCD brake switch harness connector.
- Turn ignition switch ON.
- Check voltage between ASCD brake switch terminal 1 and ground with CONSULT-II or tester.
- Voltage: Battery voltageÂ
OK or NGÂ
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Fuse block (J/B) connector M1
- 10A fuse
- Harness for open or short between ASCD brake switch and fuse
- : Repair open circuit or short to ground or short to power in harness or connectors.Â
- CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Check harness continuity between ASCD brake switch terminal 2 and ASCD clutch switch terminal 1.
Refer to WIRING DIAGRAMÂ .
- Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK : GO TO Â 9.
- NG : Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 108 and ASCD brake switch terminal 2.
Refer to WIRING DIAGRAMÂ .
- Continuity should exist.Â
- Also check harness for short to ground or short to power.
OK or NGÂ
- OK : GO TO Â 9.
- NG : GO TO 8.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors M59, F27
- Harness for open or short between ECM and ASCD brake switch
- : Repair open circuit or short to ground or short to power in harness or connectors.Â
- CHECK ASCD BRAKE SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ "
OK or NGÂ
- OK : GO TO Â 18.
- NG : Replace ASCD brake switch.
- CHECK ASCD CLUTCH SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 108 and ASCD clutch switch terminal 2. Refer to WIRING DIAGRAMÂ .
- Continuity should exist.Â
- Also check harness for short to ground or short to power.
OK or NGÂ
- OK : GO TO Â 12.
- NG : GO TO 11.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors M59, F27
- Harness for open or short between ECM and ASCD clutch switch
- : Repair open circuit or short to ground or short to power in harness or connectors.Â
- CHECK ASCD CLUTCH SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ "
OK or NGÂ
- OK : GO TO Â 18.
- NG : Replace ASCD clutch switch.
- CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect stop lamp switch harness connector.
- Check voltage between stop lamp switch terminal 1 and ground with CONSULT -II or tester.
Courtesy of NISSAN MOTOR CO., U.S.A.
- Voltage: Battery voltageÂ
OK or NGÂ
- OK : GO TO Â 15.
- NG : GO TO 14.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Fuse block (J/B) connector M2
- 10A fuse
- Harness for open or short between stop lamp switch and fuse
- : Repair open circuit or short to ground or short to power in harness or connectors.Â
- CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 101 and stop lamp switch terminal 2. Refer to WIRING DIAGRAMÂ .
- Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK : GO TO Â 17.
- NG : GO TO 16.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors M59, F27
- Harness for open or short between ECM and stop lamp switch
- : Repair open circuit or short to ground or short to power in harness or connectors.Â
- CHECK STOP LAMP SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ ".
OK or NGÂ
- OK : GO TO 18.
- NG : Replace stop lamp switch.
- CHECK INTERMITTENT INCIDENTÂ
Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ ".
- : INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
