2004 Nissan-Datsun Sentra SE-RFACTORY OEM SERVICE PROCEDURE

Inspection Procedure

WARNING: This page is about a different car, the 2004 Lexus ES 330. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK POWER DOOR LOCK OPERATION 

    NG: GO TO POWER DOOR LOCK CONTROL SYSTEM (See  INSPECTION  ) 

    OK: Go to next step. 

  2. CHECK DTC 

    Data list (for MANUAL UP/DOWN switch)

    1. Using the hand-held tester, check that DTC B1221 is output when the switch is operated.

    HINT: Using DTC "B1221" which is a code when any of the master switch is constantly turned on, the MANUAL UP/DOWN switch operation can be monitored. If there is an output of DTC "B1221" when the switch is operated, the switch circuit can be considered normal.

    Standard [Driver side J/B (body ECU) (Switch condition)]: 

    Fig 1: Driver Side J/B (Body ECU) Switch Condition Chart
    G01437100Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSY 

    OK: Go to next step. 

  3. CONFIRM REMOTE CONTROL POWER WINDOW BY MASTER SWITCH OPERATION 

    HINT:

    • When the rear door does not operate by master switch, proceed to "A".
    • When the passenger's door does not operate by master switch, proceed to "B".

    B: REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR MPX2 (D17-8) <=> MPX2 (F13-8) WIRE HARNESS 

    A: Go to next step. 

  4. CHECK CONTINUITY OF COMMUNICATION LINE 
    1. Disconnect the B5 and B6 connectors of the driver side J/B.
    2. Disconnect the R15 power window regulator switch assy rear (LH side) connector.
    3. Disconnect the R16 power window regulator switch assy rear (RH side) connector.
      Fig 2: Identifying Power Window Regulator Switch Assy Rear Terminals
      G01437101Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Check the continuity of each terminal of the disconnected connectors.

    Standard (Rear door LH): 

    Fig 3: Checking Continuity Between Communication Line Specifications Chart
    G01437102Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Standard (Rear door RH): 

    Fig 4: Checking Continuity Of Each Terminal Chart (Rear Door RH)
    G01437103Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT:

    • When the rear door LH does not inspect the continuity, proceed to "NG-A".
    • When the rear door RH does not inspect the continuity, proceed to "NG-B".

    NG-A: REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR MPX4 (B6-5) <=> MPX1 (R15-8) WIRE HARNESS 

    NG-B: REPAIR OR REPLACE WIRE HARNESS AND CONNECTOR MPX5 (B5-1) <=> MPX1 (R16-8) WIRE HARNESS 

    OK: REPLACE DRIVER SIDE JUNCTION BLOCK ASSY 

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.