Diagnostic Procedure

With CONSULT-II 

1. Start engine and warm it up to normal operating temperature.
2. Perform "VIAS SOL VALVE" in "ACTIVE TEST" mode with CONSULT-II.
   Fig 1: Identifying CONSULT-II Display - ACTIVE TEST

   Courtesy of NISSAN NORTH AMERICA, INC.
3. Turn VIAS control solenoid valve "ON" and "OFF", and make sure that power valve actuator rod moves.
   Fig 2: Identifying Power Valve Actuator

   Courtesy of NISSAN NORTH AMERICA, INC.

Without CONSULT-II 

1. Start engine and warm it up to normal operating temperature.
2. Rev engine up to between 2, 200 and 3, 300 rpm and make sure that power valve actuator rod moves.

OK or NG 

OK: INSPECTION END 

NG (With CONSULT-II): GO TO 2.

NG (Without CONSULT-II): GO TO  3.

Fig 3: Identifying Power Valve Actuator

Courtesy of NISSAN NORTH AMERICA, INC.

With CONSULT-II 

1. Stop engine and disconnect vacuum hose connected to power valve actuator.
2. Start engine and let it idle.
3. Perform "VIAS SOL VALVE" in "ACTIVE TEST" mode with CONSULT-II.
   Fig 4: Identifying CONSULT-II Display - ACTIVE TEST

   Courtesy of NISSAN NORTH AMERICA, INC.
4. Turn VIAS control solenoid valve "ON" and "OFF", and check vacuum existence under the following conditions.
   VACUUM REFERENCE
   
   

   VIAS SOL VALVE	Vacuum
   ON	Should exist.
   OFF	Should not exist.

OK or NG 

OK: Repair or replace power valve actuator.

NG: GO TO  4.

Without CONSULT-II 

1. Stop engine and disconnect vacuum hose connected to power valve actuator.
2. Disconnect VIAS control solenoid valve harness connector.
3. Start engine and let it idle.
4. Apply 12V of direct current between VIAS control solenoid valve terminals 1 and 2.
5. Check vacuum existence under the following conditions.
   VACUUM CONDITION CHART
   
   

   Condition	Vacuum
   12V direct current supply	Should exist.
   No supply	Should not exist.

   Fig 5: Applying Battery Voltage Between VIAS Control Solenoid Valve Terminals 1 And Ground

   Courtesy of NISSAN NORTH AMERICA, INC.

OK or NG 

OK: Repair or replace power valve actuator.

NG: GO TO 4.

1. Stop engine.
2. Check hoses and tubes between intake manifold and power valve actuator for crack, clogging, improper connection or disconnection. Refer to "VACUUM HOSE DRAWING ".
Fig 6: Checking Vacuum Hose
Courtesy of NISSAN NORTH AMERICA, INC.

OK or NG 

OK: GO TO 5.

NG: Repair hoses or tubes.

Refer to "COMPONENT INSPECTION ".

OK or NG 

OK: GO TO 6.

NG: Replace vacuum tank.

1. Turn ignition switch OFF.
2. Disconnect VIAS control solenoid valve harness connector.
   Fig 7: Identifying VIAS Control Solenoid Valve Harness Connector

   Courtesy of NISSAN NORTH AMERICA, INC.
3. Turn ignition switch ON.
4. Check voltage between terminal 1 and ground with CONSULT-II or tester.

   Voltage: Battery voltage 

   Fig 8: Checking Voltage Between Terminal 1 And Ground

   Courtesy of NISSAN NORTH AMERICA, INC.

OK or NG 

OK: GO TO  8.

NG: GO TO 7.

Check the following.

• Harness connectors E2, F32
• Harness for open or short between VIAS control solenoid valve and IPDM E/R
• Harness for open or short between VIAS control solenoid valve and ECM

  Repair harness or connectors.

1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between ECM terminal 29 and VIAS control solenoid valve terminal 2. Refer to Wiring Diagram .

   Continuity should exist  .

4. Also check harness for short to ground and short to power.

OK or NG 

OK: GO TO 9.

NG: Repair open circuit or short to ground or short to power in harness or connectors.

Refer to "COMPONENT INSPECTION ".

OK or NG 

OK: GO TO 10.

NG: Replace VIAS control solenoid valve.

Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

INSPECTION END