Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- CHECK OVERALL FUNCTIONÂ
- Turn ignition switch ON.
- Pinch fuel feed hose with two fingers.
Fuel pressure pulsation should be felt on the fuel feed hose for 1 second after ignition switch is turned ONÂ .
OK or NGÂ
OK : INSPECTION ENDÂ
NG : GO TO Â 2.
- CHECK FUEL PUMP POWER SUPPLY CIRCUIT-IÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Turn ignition switch ON.
- Check voltage between ECM terminal 113 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
OK : GO TO Â 5.
NG : GO TO Â 3.
- CHECK FUEL PUMP POWER SUPPLY CIRCUIT-IIÂ
Check voltage between IPDM E/R terminal 46 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
OK : GO TO Â 4.
NG : GO TO Â 12.
- 4.DETECT MALFUNCTIONING PARTÂ
Check harness for open or short between IPDM E/R and ECM
: Repair harness or connectors.
- CHECK FUEL PUMP POWER SUPPLY CIRCUIT-IIIÂ
- Turn ignition switch OFF.
- Reconnect all harness connectors disconnected.
- Disconnect "fuel level sensor unit and fuel pump" harness connector.
- Turn ignition switch ON.
- Check voltage between "fuel level sensor unit and fuel pump" terminal 1 and ground with CONSULT-II or tester.
Voltage: Battery voltage should exist for 1 second after ignition switch is turned ONÂ .
- Also check harness for short to ground and short to power.
OK or NGÂ
OK : GO TO Â 9.
NG : GO TO Â 6.
- CHECK 15A FUSEÂ
- Turn ignition switch OFF.
- Disconnect 15A fuse.
- Check 15A fuse.
OK or NGÂ
OK : GO TO Â 7.
NG : Replace fuse.
- CHECK FUEL PUMP POWER SUPPLY CIRCUIT-IVÂ
- Disconnect IPDM E/R harness connector E119.
- Check harness continuity between "fuel level sensor unit and fuel pump" terminal 1 and IPDM E/R terminal 13.
Refer to WIRING DIAGRAMÂ .
Continuity should exist .
- Also check harness for short to ground and short to power.
OK or NGÂ
OK : GO TO Â 12.
NG : GO TO Â 8.
- 8.DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors C1, E41
- Harness for open or short between "fuel level sensor unit and fuel pump" and IPDM E/R
: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK FUEL PUMP GROUND CIRCUIT FOR OPEN AND SHORTÂ
- Check harness continuity between "fuel level sensor unit and fuel pump" terminal 3 and ground. Refer to WIRING DIAGRAMÂ .
Continuity should exist .
- Also check harness for short to ground.
OK or NGÂ
OK : GO TO Â 11.
NG : GO TO Â 10.
- Check harness continuity between "fuel level sensor unit and fuel pump" terminal 3 and ground. Refer to WIRING DIAGRAMÂ .
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors C1, E41
- Harness for open or short between "fuel level sensor unit and fuel pump" and ground
: Repair open circuit or short to power in harness or connectors.
- CHECK FUEL PUMPÂ
Refer to "COMPONENT INSPECTIONÂ ".
OK or NGÂ
OK : GO TO Â 12.
NG : Replace fuel pump.
- CHECK INTERMITTENT INCIDENTÂ
Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".
OK or NGÂ
OK : Replace IPDM E/R.
NG : Repair or replace harness or connectors.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
