Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2004 Nissan-Datsun Sentra SE-RFACTORY OEM SERVICE PROCEDURE
Reference Value From Consult-II
WARNING: This page is about a different car, the 2005 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the event the output circuit (harness) is open or short circuited.
REFERENCE VALUE FROM CONSULT-II CHART
| Monitor item | Display content | Data monitor |
NOTE:
Error inspection checklist
|
|
|---|---|---|---|---|
| Condition | Reference value in normal operation | |||
| N POSI SIG | PNP switch signal ON/OFF condition | A/T shift position = N position | ON | , "CAN Communication System Inspection " |
| A/T shift position = other than N positions | OFF | |||
| P POSI SIG | PNP switch signal ON/OFF condition | A/T shift position P position | ON | , "CAN Communication System Inspection " |
| A/T shift position = other than P positions | OFF | |||
| GEAR | A/T gear position | 1st gear | 1 | - |
| 2nd gear | 2 | |||
| 3rd gear | 3 | |||
| 4th gear | 4 | |||
| 5th gear | 5 | |||
| FR RH SENSOR FR LH SENSOR RR RH SENSOR RR LH SENSOR |
Wheel speed | Vehicle stopped | 0 [km/h (MPH)] | , "WHEEL SENSOR SYSTEM " |
| Vehicle running (Note 1) | Almost in accordance with speedometer display (within +/-10%) | |||
| BATTERY VOLT | Battery voltage supplied to ABS actuator and electric unit (control unit) | Ignition switch ON | 10 to 16V | , "ABS Control Unit Power and Ground Systems Inspection " |
| STOP LAMP SW | Stop lamp switch operation | Brake pedal depressed | ON | - |
| Brake pedal not depressed | OFF | |||
| ABS WARN LAMP | ABS warning lamp ON condition (Note 2) | ABS warning lamp ON | ON | , "ABS Warning Lamp Does Not Come On When Ignition Switch Is Turned On " |
| ABS warning lamp OFF | OFF | |||
| MOTOR RELAY | Operation status of motor and motor relay | Ignition switch ON or running (ABS not activated) | OFF | , "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION " |
| Ignition switch ON or engine running (ABS activated) | ON | |||
| ACTUATOR RLY | Actuator relay operation status | Vehicle stopped (Ignition switch ON) | OFF | , "ACTUATOR MOTOR, MOTOR RELAY, AND CIRCUIT INSPECTION " |
| Vehicle stopped (Engine running) | ON | |||
| FR LH IN SOL FR LH OUT SOL FR RH IN SOL FR RH OUT SOL REAR IN SOL REAR OUT SOL |
Solenoid valve operation | Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (in fail-safe mode). | ON | , "SOLENOID VALVE SYSTEM INSPECTION " |
| When actuator (solenoid) is not active and actuator relay is active (ignition switch ON). | OFF | |||
| FLUID LEV SW | ON/OFF status of brake fluid level switch | When brake fluid level switch ON | ON | WARNING LAMPS |
| When brake fluid level switch OFF | OFF | |||
| ABS SIGNAL EBD SIGNAL |
Signal status | ABS active EBD active |
ON | ABS system EBD system |
| ABS not active EBD not active |
OFF | |||
| ABS FAIL SIG EBD FAIL SIG |
Fail signal status | ABS fail EBD fail |
ON | ABS system EBD system |
| ABS normal EBD normal |
OFF | |||
|
NOTE:
1: Confirm tire pressure is normal. Factory Service Tools Use the Manual With the Right HardwarePair factory procedures with proven DIY tools so the instructions are easier to execute. Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you. When to See a MechanicStop DIY work and contact a certified mechanic immediately if any of the following apply:
| ||||
