2004 Nissan-Datsun Sentra SE-RFACTORY OEM SERVICE PROCEDURE

Limit Switch Circuit Check Front RH

WARNING: This page is about a different car, the 2004 Nissan Titan. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH LIMIT SIGNAL 
    1. Turn ignition switch ON.
    2. Check voltage between power window and door lock/unlock switch RH connector D105 terminal 15 and ground.
    CONNECTOR TERMINAL VOLTAGE CONDITION

    Connector Terminals (Wire color) Condition Voltage (V) (Approx.)
    (+) (-)
    D105 15(G/W) Ground Passenger side door window is between fully-open and just before fully-closed position (ON) 0
    Passenger side door window is between just before fully-closed position and fully-closed position (OFF) 5
    Fig 1: Checking Voltage Between Power Window And Door Lock/Unlock Switch And Ground
    G03512372Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: Limit switch circuit is OK.
    2. NG: GO TO 2.
  2. CHECK LIMIT SWITCH GROUND CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect front power window motor RH.
    3. Check continuity between front power window motor RH connector D104 terminal 5 and ground.

      5 (G/W) - Ground: Approx. 5V 

    OK or NG 

    1. OK: GO TO 3.
    2. NG: GO TO  5 .
    Fig 2: Checking Continuity Between Front Power Window Motor And Ground
    G03512373Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK LIMIT SWITCH GROUND CIRCUIT 

    Check continuity between front power window motor RH connector D104 terminal 6 and ground.

    6 (W/B) - Ground: Continuity should exist. 

    OK or NG 

    1. OK: Replace front power window motor RH.
    2. NG: GO TO 4.
    Fig 3: Checking Continuity Between Front Power Window Motor And Ground
    G03512374Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK HARNESS CONTINUITY 
    1. Disconnect power window and door lock/unlock switch RH.
    2. Check continuity between front power window motor RH connector D104 terminal 6 and power window and door lock/unlock switch RH connector D105 terminal 3.

      6 (W/B) - 3 (W/B): Continuity should exist. 

    OK or NG 

    1. OK: Replace power window and door lock/unlock switch RH.
    2. NG: Repair or replace harness.
    Fig 4: Checking Continuity Between Front Power Window Motor And Power Window Switch
    G03512375Courtesy of NISSAN MOTOR CO., U.S.A.
  5. CHECK HARNESS CONTINUITY 
    1. Disconnect power window and door lock/unlock switch RH.
    2. Check continuity between power window and door lock/unlock switch RH connector D105 terminal 15 and front power window motor RH connector D104 terminal 5.

      15 (G/W) - 5 (G/W): Continuity should exist. 

    OK or NG 

    1. OK: Replace power window and door lock/unlock switch RH.
    2. NG: Repair or replace harness.
    Fig 5: Checking Continuity Between Power Window Switch And Front Power Window Motor Connector Terminal
    G03512376Courtesy of NISSAN MOTOR CO., U.S.A.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.