Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Daytime Light Control Does Not Operate Properly
- FOG LAMP ACTIVE TEST
With CONSULT-II
- Select "IPDM E/R" on CONSULT-II. and select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
- Select "LAMPS" on "SELECT TEST ITEM" screen.
- Touch "FOG" screen.
- Make sure fog lamp operation.
Fog lamp should operate.
Without CONSULT-II
- Start auto active test. .
- Make sure fog lamp operation.
Fog lamp should operate.
OK or NG
- OK: GO TO 5.
- NG: GO TO 2.
- CHECK FRONT FOG LAMP INPUT SIGNAL
With CONSULT-II
- Turn ignition switch OFF.
- Disconnect front combination lamp RH and LH connectors.
- Select "IPDM E/R" on CONSULT-II. and select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
- Select "LAMPS" on "SELECT TEST ITEM" screen.
- Touch "FOG" screen.
- When fog lamp is operating, check voltage between front fog lamp RH and LH harness connector and ground.VOLTAGE CHECK CHART
Terminals Voltage (+) (-) Connector Terminal (Wire color) RH E94 1 (G/W) Ground Battery voltage LH E92 1 (W/R)
Without CONSULT-II
- Turn ignition switch OFF.
- Disconnect front fog lamp RH and LH connectors.
- Start auto active test. .
- When fog lamp is operating, check voltage between front fog lamp RH and LH harness connectors and ground.VOLTAGE CHECK CHART
Terminals Voltage (+) (-) Connector Terminal (Wire color) RH E94 1 (G/W) Ground Battery voltage LH E92 1 (W/R)
OK or NG
- OK: GO TO 4.
- NG: GO TO 3.
- CHECK FRONT FOG LAMP CIRCUIT
- Turn ignition switch OFF.
- Disconnect IPDM E/R connector.
- Check continuity between IPDM E/R harness connector E8 terminal 36 (G/W) and front fog lamp RH harness connector E94 terminal 1 (G/W).
36 (G/W) - 1 (G/W): Continuity should exist.
- Check continuity between IPDM E/R harness connector E8 terminal 37 (W/R) and front fog lamp LH harness connector E92 terminal 1 (W/R).
37 (W/R) - 1 (W/R): Continuity should exist.
OK or NG
- OK: Replace IPDM E/R.
- NG: Repair harness or connector.
- CHECK FRONT FOG LAMP GROUND
- Check continuity between front fog lamp RH harness connector E94 terminal 2 (B) and ground.
2 (B) - Ground: Continuity should exist.
- Check continuity between front fog lamp LH harness connector E92 terminal 2 (B) and ground.
2 (B) - Ground: Continuity should exist.
OK or NG
- OK: Check front fog lamp bulbs.
- NG: Repair harness or connector.
- Check continuity between front fog lamp RH harness connector E94 terminal 2 (B) and ground.
- CHECK SELF-DIAGNOSIS
Select "BCM" on CONSULT-II. Carry out "BCM" self-diagnosis.
Displayed results of self-diagnosis
- No malfunction detected: Replace BCM. Refer to "REMOVAL AND INSTALLATION OF BCM " .
- CAN communications or CAN system: Check BCM CAN communication system. Refer to "CAN COMMUNICATION INSPECTION USING CONSULT-II (SELF-DIAGNOSIS) " .
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
