2004 Nissan-Datsun Sentra SE-RFACTORY OEM SERVICE PROCEDURE

Rear Power Window Regulator (LH) Circuit Check

WARNING: This page is about a different car, the 2003 Nissan Murano. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK REAR POWER WINDOW SWITCH (LH) OUTPUT SIGNAL
    1. Turn ignition switch OFF.
    2. Disconnect rear power window regulator (LH).
    3. Turn ignition switch ON.
    4. Check voltage between rear power window switch (LH) connector D52 terminals 1 and 2 and ground.
    CONNECTOR TERMINAL VOLTAGE

    Connector Terminals (Wire color) Condition Voltage (V) (Approx.)
    (+) (-)
    D52 1 (G) Ground Closing 0
    Opening Battery voltage
    2 (L) Closing Battery voltage
    Opening 0

    OK or NG

    1. OK : Replace rear power window motor (LH).
    2. NG : GO TO 2.
    Fig 1: Checking Voltage Between Rear Power Window Switch (LH) Connector D52 Terminals 1 And 2 And Ground
    G03358876Courtesy of NISSAN MOTOR CO., U.S.A.
  2. CHECK HARNESS CONTINUITY 1 
    1. Turn ignition switch OFF.
    2. Disconnect rear power window switch (LH) connector.
    3. Check continuity between rear power window switch (LH) connector D55 terminal 4, 5 and rear power window regulator (LH) connector D52 terminals 1, 2.
      1. 4 (G) - 1 (G) : Continuity should exist. 
      2. 5 (L) - 2 (L) : Continuity should exist. 

    OK or NG

    1. OK : GO TO 3.
    2. NG : Repair or replace harness between rear power window switch (LH) and rear power window regulator (LH).
    Fig 2: Checking Continuity Between Rear Power Window Switch (LH) Connector D55 Terminal 4, 5 And Rear Power Window Regulator (LH) Connector D52 Terminals 1, 2
    G03358877Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK REAR POWER WINDOW SWITCH (LH) POWER SUPPLY 
    1. Connect rear power window switch (LH) connector.
    2. Turn ignition switch ON.
    3. Check voltage between rear power window switch (LH) connector D55 terminal 1 and ground.
      1. 1 (W/L) - Ground : Battery voltage 

    OK or NG

    1. OK : GO TO 4.
    2. NG : Repair or replace harness.
    Fig 3: Checking Voltage Between Rear Power Window Switch (LH) Connector D55 Terminal 1 And Ground
    G03358878Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK REAR POWER WINDOW SWITCH LH 
    1. Turn igniting switch OFF.
    2. Disconnect rear power window switch (LH) connector.
    3. Check continuity between rear power window switch (LH) connector D55 terminals 1, 2, 3 and 4, 5.
    CONNECTOR TERMINAL CONTINUITY

    Terminal Switch condition Continuity
    1 4 DOWN position Yes
    3 Free
    1 5 UP position
    2 Free

    OK or NG

    1. OK : GO TO 5.
    2. NG : Replace rear power window switch (LH).
    Fig 4: Checking Continuity Between Rear Power Window Switch (LH) Connector D55 Terminals 1, 2, 3 And 4, 5
    G03358879Courtesy of NISSAN MOTOR CO., U.S.A.
  5. CHECK POWER WINDOW MAIN SWITCH OUTPUT SIGNAL 
    1. Turn ignition switch ON.
    2. Power window main switch is operated, check voltage between power window main switch connector D6 terminals 1 and 3.
    CONNECTOR TERMINAL VOLTAGE

    Connector Terminals (Wire color) Condition Voltage (V) (Approx.)
    (+) (-)
    D6 1 (Y) Ground Closing Battery voltage
    Opening 0
    3 (R) Closing 0
    Opening Battery voltage

    OK or NG

    1. OK : GO TO 6.
    2. NG : Replace power window main switch.
    Fig 5: Checking Voltage Between Power Window Main Switch Connector D6 Terminals 1 And 3 And Ground
    G03358880Courtesy of NISSAN MOTOR CO., U.S.A.
  6. CHECK HARNESS CONTINUITY 
    1. Turn ignition switch OFF.
    2. Disconnect power window main switch connector.
    3. Check continuity between power window main switch connector D6 terminals 1, 3 and rear power window switch (LH) connector D55 terminals 2, 3.
      1. 1 (Y) - 2 (Y) : Continuity should exist. 
      2. 3 (R) - 3 (R) : Continuity should exist. 

    OK or NG

    1. OK : Check the condition of the harness and the connector.
    2. NG : Repair or replace harness between power window main switch and rear power window switch (LH).
    Fig 6: Checking Continuity Between Power Window Main Switch Connector D6 Terminals 1, 3 And Rear Power Window Switch (LH) Connector D55 Terminals 2, 3
    G03358881Courtesy of NISSAN MOTOR CO., U.S.A.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.