2004 Nissan-Datsun Sentra SE-RFACTORY OEM SERVICE PROCEDURE

A/T Models Except ULEV

  1. CHECK EXHAUST SYSTEM 

    Visually check exhaust tubes and muffler for dent.

    OK or NG 

    1. OK: GO TO 2.
    2. NG: Repair or replace.
  2. CHECK EXHAUST GAS LEAK 
    1. Start engine and run it at idle.
    2. Listen for an exhaust gas leak before the three way catalyst (manifold).
      Fig 1: Checking Exhaust Gas Leak
      G00777921Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 3.
    2. NG: Repair or replace.
  3. CHECK INTAKE AIR LEAK 

    Listen for an intake air leak after the mass air flow sensor.

    OK or NG 

    1. OK: GO TO 4.
    2. NG: Repair or replace.
  4. CHECK IGNITION TIMING 

    Check for ignition timing. Refer to "BASIC INSPECTION ".

    Fig 2: Target Idle Speed & Ignition Timing Specifications
    G00777922Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 5.
    2. NG: Follow the Basic Inspection.
  5. CHECK INJECTORS 
    1. Refer to WIRING DIAGRAM  for Injectors.
    2. Stop engine and then turn ignition switch ON.
    3. Check voltage between ECM terminals 22, 23, 41, 42 and ground with CONSULT-II or tester.

      Battery voltage should exist. 

    4. Fig 3: Checking Injectors
      G00777923Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 6.
    2. NG: Perform DIAGNOSTIC PROCEDURE , INJECTOR.
  6. CHECK IGNITION SPARK 
    1. Turn ignition switch OFF.
    2. Disconnect ignition coil assembly from rocker cover.
    3. Connect a known-good spark plug to the ignition coil assembly.
    4. Place end of spark plug against a suitable ground and crank engine.
    5. Check for spark.
    6. Fig 4: Checking Ignition Spark
      G00777924Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    1. OK: GO TO 7.
    2. NG: Check ignition coil with power transistor and their circuit.
  7. CHECK INJECTOR 
    1. Turn ignition switch OFF.
    2. Remove injector assembly. Refer to "FUEL INJECTOR AND FUEL TUBE ". Keep fuel hose and all injectors connected to injector gallery.
    3. Disconnect ignition coil assembly harness connector.
    4. Turn ignition switch ON.

      Make sure fuel does not drip from injector.

    OK or NG 

    1. OK (Does not drip): GO TO 8.
    2. NG (Drips): Replace the injector(s) from which fuel is dripping.
  8. CHECK INTERMITTENT INCIDENT 

    Perform "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

    1. Trouble is fixed: INSPECTION END 
    2. Trouble is not fixed: Replace three way catalyst (manifold).
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.