Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- CHECK OVERALL FUNCTIONÂ
With CONSULT-IIIÂ
- Start engine and warm it up to normal operating temperature.
- Perform "VIAS SOL VALVE" in "ACTIVE TEST" mode with CONSULT-III.
- Turn VIAS control solenoid valve ON and OFF and make sure that power valve actuator rod moves.
Without CONSULT-IIIÂ
- Start engine and warm it up to normal operating temperature.
- Rev engine up to between 1, 800 and 3, 600 rpm and make sure that power valve actuator rod (2) moves as shown in the figure.
- Power valve actuator (1)
OK or NGÂ
OK: INSPECTION ENDÂ
NG (With CONSULT-III): GO TO Â 2.
NG (Without CONSULT-III): GO TO Â 3.
- CHECK VACUUM EXISTENCEÂ
With CONSULT-IIIÂ
- Stop engine and disconnect vacuum hose connected to power valve actuator.
- Install the vacuum gauge as shown in Fig 3.
- Start engine and let it idle.
- Perform "VIAS SOL VALVE" in "ACTIVE TEST" mode with CONSULT-III.
- Turn VIAS control solenoid valve ON and OFF, and check vacuum existence under the following conditions.VIAS SOL VALVE SPECIFICATION
VIAS SOL VALVE Vacuum ON Should exist. OFF Should not exist.
OK or NGÂ
OK: Repair or replace power valve actuator.
NG: GO TO Â 4.
- CHECK VACUUM EXISTENCEÂ
Without CONSULT-IIIÂ
- Stop engine and disconnect vacuum hose connected to power valve actuator.
- Install the vacuum gauge as shown in Fig 4.
- Disconnect VIAS control solenoid valve harness connector.
- Start engine and let it idle.
- Apply 12V of direct current between VIAS control solenoid valve terminals 1 and 2.
- Check vacuum existence under the following conditions.VACUUM CONDITIONS CHART
Condition Vacuum 12V direct current supply Should exist No supply Should not exist
OK or NGÂ
OK: Repair or replace power valve actuator.
NG: GO TO Â 4.
- CHECK VACUUM HOSEÂ
- Stop engine.
- Check hoses and tubes between intake manifold and power valve actuator for crack, clogging, improper connection or disconnection. Refer to "VACUUM HOSE DRAWING ."
OK or NGÂ
OK: GO TO Â 5.
NG: Repair hoses or tubes.
- CHECK VACUUM TANKÂ
Refer to "COMPONENT INSPECTIONÂ ."
OK or NGÂ
OK: GO TO Â 6.
NG: Replace vacuum tank.
- CHECK VIAS CONTROL SOLENOID VALVE POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect VIAS control solenoid valve (2) harness connector.
- Power valve actuator (1)
- Turn ignition switch ON.
- Check voltage between terminal 1 and ground with CONSULT-III or tester.
Voltage: Battery voltageÂ
OK or NGÂ
OK: GO TO Â 8.
NG: GO TO Â 7.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E131, M92
- Harness connectors M70, F58
- Harness for open or short between VIAS control solenoid valve and IPDM E/R
- Harness for open or short between VIAS control solenoid valve and ECM
>> Repair harness or connectors.
- CHECK VIAS CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 29 and VIAS control solenoid valve terminal 2.
Refer to Wiring Diagram.
Continuity should exist .
- Also check harness for short to ground and short to power.
OK or NGÂ
OK: GO TO Â 9.
NG: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK VIAS CONTROL SOLENOID VALVEÂ
Refer to "COMPONENT INSPECTIONÂ ."
OK or NGÂ
OK: GO TO Â 10.
NG: Replace VIAS control solenoid valve.
- CHECK INTERMITTENT INCIDENTÂ
Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ."
>>INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
