Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- CHECK GROUND CONNECTIONSÂ
- Turn ignition switch OFF.
- Loosen and retighten ground three screws on the body. Refer to GROUND INSPECTIONÂ .
OK or NGÂ
- OK: GO TO 2.
- NG: Repair or replace ground connections.
- CHECK CONNECTORÂ
- Disconnect EVAP control system pressure sensor harness connector.
- Check sensor harness connector for water.
- Water should not exist.Â
OK or NGÂ
- OK: GO TO 3.
- NG: Repair or replace harness connector.
- CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUITÂ
- Turn ignition switch ON.
- Check voltage between EVAP control system pressure sensor terminal 3 and ground with CONSULT-II or tester.
- Voltage: Approximately 5VÂ
OK or NGÂ
- OK: GO TO Â 5 .
- NG: GO TO 4.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors B106, E138
- Harness connectors E19, F33
- Harness for open or short between EVAP control system pressure sensor and ECM
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Disconnect TCM harness connector.
- Check harness continuity between EVAP control system pressure sensor terminal 1 and ECM terminal 67, TCM terminal 42.
Refer to WIRING DIAGRAMÂ .
- Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO Â 7 .
- NG: GO TO 6.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E19, F33
- Harness connectors B106, E138
- Harness for open or short between EVAP control system pressure sensor and ECM
- Harness for open or short between EVAP control system pressure sensor and TCM
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Check harness continuity between ECM terminal 32 and EVAP control system pressure sensor terminal 2.
Refer to WIRING DIAGRAMÂ .
- Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO Â 9 .
- NG: GO TO 8.
- Check harness continuity between ECM terminal 32 and EVAP control system pressure sensor terminal 2.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E19, F33
- Harness connectors B106, E138
- Harness for open or short between EVAP control system pressure sensor and ECM
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK RUBBER TUBE FOR CLOGGINGÂ
- Disconnect rubber tube connected to EVAP canister vent control valve.
- Check the rubber tube for clogging.
OK or NGÂ
- OK: GO TO 10.
- NG: Clean the rubber tube using an air blower.
- CHECK EVAP CANISTER VENT CONTROL VALVEÂ
Refer to COMPONENT INSPECTIONÂ .
OK or NGÂ
- OK: GO TO 11.
- NG: Replace EVAP canister vent control valve.
- CHECK EVAP CONTROL SYSTEM PRESSURE SENSORÂ
Refer to COMPONENT INSPECTIONÂ .
OK or NGÂ
- OK: GO TO 12.
- NG: Replace EVAP control system pressure sensor.
- CHECK RUBBER TUBEÂ
Check obstructed rubber tube connected to EVAP canister vent control valve.
OK or NGÂ
- OK: GO TO 13.
- NG: Clean rubber tube using an air blower, repair or replace rubber tube.
- CHECK WATER SEPARATORÂ
Refer to COMPONENT INSPECTIONÂ .
OK or NGÂ
- OK: GO TO 14.
- NG: Replace water separator.
- CHECK IF EVAP CANISTER SATURATED WITH WATERÂ
- Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor attached.
- Check if water will drain from the EVAP canister.
Yes or NoÂ
- Yes: GO TO 15.
- No: GO TO Â 17 .
- CHECK EVAP CANISTERÂ
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor attached.
The weight should be less than 2.1 kg (4.6 Ib).Â
OK or NGÂ
- OK: GO TO Â 17 .
- NG: GO TO 16.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- EVAP canister for damage
- EVAP hose between EVAP canister and water separator for clogging or poor connection
- Repair hose or replace EVAP canister.
- CHECK INTERMITTENT INCIDENTÂ
Refer to TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTÂ .
- INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
