2003 Nissan-Datsun Sentra SE-R, AutomaticFACTORY OEM SERVICE PROCEDURE

Control Valve Assembly: Assembly

WARNING: This page is about a different variant/trim than selected.
  1. Install upper, inter and lower body.
    1. Place oil circuit of upper body face up. Install steel balls in their proper positions.
    2. Fig 1: Identifying Proper Position Of Steel Balls
      G01319604Courtesy of NISSAN MOTOR CO., U.S.A.
    3. Install upper separating gasket, upper inter separating gasket and upper separating plate in order shown in illustration.
      Fig 2: Installing Upper Separating Gasket, Upper Inter Separating Gasket And Upper Separating Plate
      G01319605Courtesy of NISSAN MOTOR CO., U.S.A.
      • Always use new gaskets. 
    4. Install reamer bolts F  from bottom of upper body. Using reamer bolts as guides, install separating plate and gaskets as a set.
      Fig 3: Installing Reamer Bolts From Bottom Of Upper Body
      G01319606Courtesy of NISSAN MOTOR CO., U.S.A.
    5. Install pilot filter.
      Fig 4: Installing Pilot Filter
      G01319607Courtesy of NISSAN MOTOR CO., U.S.A.
    6. Place inter body as shown in the illustration. Install steel balls in their proper positions.
      Fig 5: Identifying Proper Position Of Steel Balls
      G01319608Courtesy of NISSAN MOTOR CO., U.S.A.
    7. Install inter body on upper body using reamer bolts F  as guides.
      Fig 6: Installing Inter Body On Upper Body Using Reamer Bolts
      G01319609Courtesy of NISSAN MOTOR CO., U.S.A.
      • Be careful not to dislocate or drop steel balls. 
    8. Install steel balls, oil cooler relief valve springs and T/C pressure holding spring in their proper positions in lower body.
      Fig 7: Installing Steel Balls, Oil Cooler Relief Valve Springs And T/C Pressure Holding Spring
      G01319610Courtesy of NISSAN MOTOR CO., U.S.A.
    9. Install lower separating gasket, inter separating gasket and lower separating plate in order shown in the illustration.
      Fig 8: Installing Lower Separating Gasket, Inter Separating Gasket And Lower Separating Plate
      G01319611Courtesy of NISSAN MOTOR CO., U.S.A.
    10. Install bolts E  from bottom of lower body. Using bolts E  as guides, install separating plate and gaskets as a set.
      Fig 9: Installing Bolts From Bottom Of Lower Body
      G01319612Courtesy of NISSAN MOTOR CO., U.S.A.
    11. Install support plates on lower body.
    12. Install lower body on inter body using reamer bolts F  as guides and tighten reamer bolts F  slightly.
      Fig 10: Installing Lower Body On Inter Body Using Reamer Bolts
      G01319613Courtesy of NISSAN MOTOR CO., U.S.A.
  2. Install O-rings to solenoid valves and terminal body.
    • Apply ATF to O-rings. 
  3. Fig 11: Installing O-Rings To Solenoid Valves And Terminal Body
    G01319614Courtesy of NISSAN MOTOR CO., U.S.A.
  4. Install and tighten bolts.

    Bolt length, number and location: 

    Fig 12: Identifying Bolt Length And Number Of Bolts
    G01319615Courtesy of NISSAN MOTOR CO., U.S.A.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.