2003 Nissan-Datsun Sentra SE-R, AutomaticFACTORY OEM SERVICE PROCEDURE

Terminals and Reference Values for BCM

WARNING: This page is about a different car, the 2006 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
BCM TERMINALS AND REFERENCE VALUE TABLE

Terminal No. Wire color Signal name Measuring condition Reference value (Approx.)
Ignition switch Operation or condition
2 GR/R Combination switch input 5 ON Lighting, turn, wiper OFF
Wiper dial position 4
G04151975Courtesy of NISSAN MOTOR CO., U.S.A.
3 G/Y Combination switch input 4 ON Lighting, turn, wiper OFF
Wiper dial position 4
G04136997Courtesy of NISSAN MOTOR CO., U.S.A.
4 G/R Combination switch input 3 ON Lighting, turn, wiper OFF
Wiper dial position 4
G04151975Courtesy of NISSAN MOTOR CO., U.S.A.
5 G/B Combination switch input 2 ON Lighting, turn, wiper OFF
Wiper dial position 4
G04200797Courtesy of NISSAN MOTOR CO., U.S.A.
6 G/W Combination switch input 1
11 V Ignition switch (ACC) ACC - Battery voltage
12 GR/L Front door switch RH signal OFF Front door switch RH ON (open) 0V
OFF (closed) Battery voltage
13 O/B Sliding door switch RH signal OFF Sliding door switch RH ON (open) 0V
OFF (closed) Battery voltage
18 P Sensor ground ON - 0V
32 R/G Combination switch output 5 ON Lighting, turn, wiper OFF
Wiper dial position 4
G04200798Courtesy of NISSAN MOTOR CO., U.S.A.
33 R/Y Combination switch output 4 ON Lighting, turn, wiper OFF
Wiper dial position 4
G04136997Courtesy of NISSAN MOTOR CO., U.S.A.
34 R Combination switch output 3 ON Lighting, turn, wiper OFF
Wiper dial position 4
G04200800Courtesy of NISSAN MOTOR CO., U.S.A.
35 R/B Combination switch output 2 ON Lighting, turn, wiper OFF
Wiper dial position 4
G04136997Courtesy of NISSAN MOTOR CO., U.S.A.
36 R/W Combination switch output 1
38 G Ignition switch (ON) ON - Battery voltage
39 L CAN-H - - -
40 P CAN-L - - -
42 Y/G Battery power supply OFF - Battery voltage
43 W/R Optical sensor signal ON When optical sensor is illuminated 3.1 V or moreNote
When optical sensor is not illuminated 0.6 V or less
52 B/W Ground ON - 0V
55 W/B Battery power supply OFF - Battery voltage
58 O Back door latch (door ajar switch) signal OFF Back door latch (door ajar switch) ON (open) 0V
OFF (closed) Battery voltage
62 GR/R Front door switch LH signal OFF Front door switch LH ON (open) 0V
OFF (closed) Battery voltage
63 W/G Sliding door switch LH signal OFF Sliding door switch LH ON (open) 0V
OFF (closed) Battery voltage
NOTE: Optical sensor must be completely subjected to work lamp light. If the optical sensor is insufficiently illuminated, the measured value may not satisfy standard.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.