2003 Nissan-Datsun Sentra SE-R, AutomaticFACTORY OEM SERVICE PROCEDURE

BOSE(R) System: Notes

WARNING: This page is about a different car, the 2004 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.

Refer to Owner's Manual for audio system operating instructions.

Power is supplied at all times

  • Through 15A fuse [No. 18, located in the fuse block (J/B)]
  • To subwoofer terminal 6
  • Through 20A fuse [No. 31, located in the fuse and fusible link box]
  • To audio unit terminal 6 and
  • To BOSE speaker amp. terminal 1
  • Through 15A fuse [No. 19, located in the fuse block (J/B)]
  • To AV switch terminal 1 and
  • To display unit terminal 1 (without NAVI) or display control unit terminal 1 (with NAVI).

With the ignition switch in the ACC or ON position, power is supplied

  • Through 10A fuse [No. 4, located in the fuse block (J/B)]
  • To audio unit terminal 10 and
  • To AV switch terminal 2 and
  • To display unit terminal 2 (without NAVI) or display control unit terminal 10 (with NAVI).

With the ignition switch in the ON or START position, power is supplied

  • Through 10A fuse [No. 12, located in the fuse block (J/B)]
  • To display unit terminal 3 (without NAVI) or display control unit terminal 12 (with NAVI).

Ground is supplied through the case of the audio unit.

Ground is also supplied

  • To subwoofer terminal 5
  • Through body grounds B7 and B19 and
  • To BOSE speaker amp. terminal 17
  • To AV switch terminal 5 and
  • To display unit terminal 6 (without NAVI) or terminal 1 (with NAVI) and
  • To display control unit terminal 3 (with NAVI)
  • Through body grounds M57, M61 and M79.

Then audio signals are supplied

  • Through audio unit terminals 1, 2, 3, 4,13, 14,15 and 16
  • To Bose speaker amp. terminals 23, 24, 25, 26, 27, 28, 29 and 30.

Audio signals are amplified by the BOSE speaker amp.

The amplified audio signals are supplied

  • Through BOSE speaker amp. terminals 2, 3, 9,10,11,12, 13, 14, 15, 16, 18 and 19
  • To terminals + and - of front door speaker LH and RH and
  • To terminals + and - of front tweeter LH and RH and
  • To terminals + and - of center speaker and
  • To terminals + and - of rear speaker LH and RH and
  • To terminals + and - of rear tweeter LH and RH and
  • To terminals 1 and 2 of subwoofer.

When one of steering wheel audio control switches is pushed, the resistance in steering switch circuit changes depending on which button is pushed.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.