Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
M/T Models
- CHECK OVERALL FUNCTION-IÂ
With CONSULT-IIÂ
- Turn ignition switch ON.
- Select "BRAKE SW1" in "DATA MONITOR" mode with CONSULT-II.
- Check "BRAKE SW1" indication under the following conditions.CONDITION INDICATION
CONDITION INDICATION Brake pedal and/or clutch pedal: Slightly depressed OFF Brake pedal and clutch pedal: Fully released ON
Without CONSULT-IIÂ
- Turn ignition switch ON.
- Check voltage between ECM terminal 108 and ground under the following conditions.TERMINALS VOLTAGE REFERENCE
CONDITION VOLTAGE Brake pedal and/or clutch pedal: Slightly depressed Approximately 0V Brake pedal and clutch pedal: Fully released Battery voltage
OK or NGÂ
- OK: GO TO 2.
- NG: GO TO Â 3.
- CHECK OVERALL FUNCTION-IIÂ
With CONSULT-IIÂ
Check "BRAKE SW2" indication in "DATA MONITOR" mode.
CONDITION INDICATIONCONDITION INDICATION Brake pedal: Fully released OFF Brake pedal: Slightly depressed ON Without CONSULT-IIÂ
Check voltage between ECM terminal 101 and ground under the following conditions.
TERMINALS VOLTAGE REFERENCECONDITION VOLTAGE Brake pedal: Fully released Approximately 0V Brake pedal: Slightly depressed Battery voltage OK or NGÂ
- OK: INSPECTION ENDÂ
- NG: GO TO Â 11.
- CHECK ASCD BRAKE SWITCH CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect ASCD clutch switch harness connector.
- Turn ignition switch ON.
- Check voltage between ASCD clutch switch terminal 1 and ground under the following conditions with CONSULT-II or tester.TERMINALS VOLTAGE REFERENCE
CONDITION VOLTAGE Brake pedal: Fully released Battery voltage Brake pedal: Slightly depressed Approximately 0V
OK or NGÂ
- OK: GO TO Â 8.
- NG: GO TO 4.
- CHECK ASCD BRAKE SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect ASCD brake switch harness connector.
- Turn ignition switch ON.
- Check voltage between ASCD brake switch terminal 1 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
- OK: GO TO Â 6.
- NG: GO TO 5.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Fuse block (J/B) connector E101
- 10A fuse
- Harness for open or short between ASCD brake switch and fuse
Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ASCD BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Check harness continuity between ASCD brake switch terminal 2 and ASCD clutch switch terminal 1.
Refer to WIRING DIAGRAMÂ .
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO 7.
- NG: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ASCD BRAKE SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ "
OK or NGÂ
- OK: GO TO Â 16.
- NG: Replace ASCD brake switch.
- CHECK ASCD CLUTCH SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between ASCD clutch switch terminal 2 and ECM terminal 108.
Refer to WIRING DIAGRAMÂ .
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO Â 10.
- NG: GO TO 9.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E10, F1
- Harness for open or short between ECM and ASCD clutch switch
Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK ASCD CLUTCH SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ ".
OK or NGÂ
- OK: GO TO Â 16.
- NG: Replace ASCD clutch switch.
- CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUITÂ
- Turn ignition switch OFF.
- Disconnect stop lamp switch harness connector.
- Check voltage between stop lamp switch terminal 1 and ground with CONSULT-II or tester.
Voltage: Battery voltageÂ
OK or NGÂ
- OK: GO TO Â 13.
- NG: GO TO 12.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Fuse block (J/B) connector E101
- 10A fuse
- Harness for open or short between stop lamp switch and battery
Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORTÂ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminal 101 and stop lamp switch terminal 2.
Refer to WIRING DIAGRAMÂ .
Continuity should exist.Â
- Also check harness for short to ground and short to power.
OK or NGÂ
- OK: GO TO Â 15.
- NG: GO TO 14.
- DETECT MALFUNCTIONING PARTÂ
Check the following.
- Harness connectors E108, M15
- Harness connectors M72, F102
- Harness for open or short between ECM and stop lamp switch
Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK STOP LAMP SWITCHÂ
Refer to "COMPONENT INSPECTIONÂ
OK or NGÂ
- OK: GO TO 16.
- NG: Replace stop lamp switch.
- CHECK INTERMITTENT INCIDENTÂ
Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".
INSPECTION ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
