Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Diagnostic Procedure
- CHECK ENGINE STARTĀ
Turn ignition switch OFF, and restart engine.
Is engine running?Ā
Yes or NoĀ
- CHECK OVERALL FUNCTIONĀ
With CONSULT-IIĀ
- Perform "POWER BALANCE" in "ACTIVE TEST" mode with CONSULT-II.
- Make sure that each circuit produces a momentary engine speed drop.
OK or NGĀ
- OK: INSPECTION END
- NG: GO TO Ā 10 .
- CHECK OVERALL FUNCTIONĀ
Without CONSULT-IIĀ
- Let engine idle.
- Read the voltage signal between ECM terminals 60, 61, 62, 79, 80, 81 and ground with an oscilloscope.
- Verify that the oscilloscope screen shows the signal wave as shown below.
Courtesy of NISSAN MOTOR CO., U.S.A.
OK or NGĀ
- OK: INSPECTION END
- NG: GO TO Ā 10 .
- CHECK IGNITION COIL POWER SUPPLY CIRCUIT-IĀ
- Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
- Check voltage between ECM terminals 119, 120 and ground with CONSULT-II or tester.
Courtesy of NISSAN MOTOR CO., U.S.A.
- Voltage: Battery voltageĀ
OK or NGĀ
- OK: GO TO 5.
- NG: Go to POWER SUPPLY AND GROUND CIRCUITĀ .
- CHECK IGNITION COIL POWER SUPPLY CIRCUIT-IIĀ
- Turn ignition switch OFF.
- Disconnect condenser harness connector.
- Turn ignition switch ON.
- Check voltage between condenser terminal + and ground with CONSULT-II or tester.
- Voltage: Battery voltageĀ
OK or NGĀ
- OK: GO TO Ā 8 .
- NG: GO TO 6.
- CHECK IGNITION COIL POWER SUPPLY CIRCUIT-IIIĀ
- Turn ignition switch OFF.
- Disconnect IPDM E/R harness connector E122.
- Check harness continuity between IPDM E/R terminal 35 and condenser terminal +. Refer to WIRING DIAGRAMĀ
.
- Continuity should exist.Ā
- Also check harness for short to ground and short to power.
OK or NGĀ
- OK: GO TO Ā 17 .
- NG: GO TO 7.
- DETECT MALFUNCTIONING PARTĀ
Check the following.
- Harness connectors E5, F14
- Harness for open or short between IPDM E/R and condenser
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK CONDENSER GROUND CIRCUIT FOR OPEN AND SHORTĀ
- Turn ignition switch OFF.
- Check harness continuity between condenser terminal - and engine ground. Refer to WIRING DIAGRAMĀ
.
- Continuity should exist.Ā
- Also check harness for short to power.
OK or NGĀ
- OK: GO TO 9.
- NG: Repair open circuit or short to power in harness or connectors.
- CHECK CONDENSERĀ
Refer to COMPONENT INSPECTIONĀ .
OK or NGĀ
- OK: GO TO Ā 10 .
- NG: Replace condenser.
- CHECK IGNITION COIL POWER SUPPLY CIRCUIT-VĀ
- Turn ignition switch OFF.
- Reconnect all harness connectors disconnected.
- Disconnect ignition coil harness connector.
- Turn ignition switch ON.
- Check voltage between ignition coil terminal 3 and ground with CONSULT-II or tester.
Courtesy of NISSAN MOTOR CO., U.S.A.
- Voltage: Battery voltageĀ
OK or NGĀ
- OK: GO TO Ā 12 .
- NG: GO TO 11.
- DETECT MALFUNCTIONING PARTĀ
Check the following.
- Harness connectors F43, F201
- Harness for open or short between ignition coil and harness connector F35
- Repair or replace harness or connectors.
- CHECK IGNITION COIL GROUND CIRCUIT FOR OPEN AND SHORTĀ
- Turn ignition switch OFF.
- Check harness continuity between ignition coil terminal 2 and engine ground.
Refer to WIRING DIAGRAMĀ .
- Continuity should exist.Ā
- Also check harness for short to power.
OK or NGĀ
- OK: GO TO Ā 14 .
- NG: GO TO 13.
- DETECT MALFUNCTIONING PARTĀ
Check the following.
- Harness connectors F201, F43
- Harness for open or short between ignition coil and engine ground
- Repair open circuit or short to power in harness or connectors.
- CHECK IGNITION COIL OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORTĀ
- Disconnect ECM harness connector.
- Check harness continuity between ECM terminals 60, 61, 62, 79, 80, 81 and ignition coil terminal 1. Refer to WIRING DIAGRAMĀ
.
- Continuity should exist.Ā
- Also check harness for short to ground and short to power.
OK or NGĀ
- OK: GO TO Ā 16 .
- NG: GO TO 15.
- DETECT MALFUNCTIONING PARTĀ
Check the following.
- Harness connectors F43, F201
- Harness for open or short between ignition coil and ECM
- Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK IGNITION COIL WITH POWER TRANSISTORĀ
Refer to COMPONENT INSPECTIONĀ ".
OK or NGĀ
- OK: GO TO 17.
- NG: Replace ignition coil with power transistor.
- CHECK INTERMITTENT INCIDENTĀ
Refer to TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENTĀ .
- INSPECTION ENDĀ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- ⢠You smell fuel, burning insulation, or see smoke.
- ⢠Brakes feel soft, pull hard to one side, or make grinding noises.
- ⢠The engine overheats, stalls repeatedly, or misfires under load.
- ⢠You are missing required tools, torque specs, or safe lifting equipment.
- ⢠You are not confident in the next step or safety outcome.
