Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Nissan-Datsun Sentra SE-R L4-2.5L (QR25DE)FACTORY OEM SERVICE PROCEDURE
Engine Controls - ECM Programming Information: Overview
Classification: EC99-013D
Reference: NTB00-006D
Date: May 12, 2006
ECM REPROGRAMMING FOR NISSAN VEHICLES
This amended version (NTB00-006d) updates the Service Procedure Section. Please discard all previously released copies of NTB00-006.
APPLIED VEHICLES: 1999 Frontier (D22)
1999 Quest (V41)
1999.5 Pathfinder (R50)
All 2000 and later
SERVICE INFORMATION
^ In-vehicle ECM reprogramming is available to update the ECM of certain 1999 vehicles (listed in Applied Vehicles above), and all 2000 and later vehicles.
^ This reprogramming allows the vehicle ECM to be upgraded to the latest operating specifications without removal or replacement of the ECM.
^ When an ECM has been reprogrammed it will display a new P/N on the CONSULT-II screen.
NOTE:
ECM reprogramming will not affect NATS.
^ ECM reprogramming requires the use of ASIST 8.0 or higher, and CONSULT-II with the ECU Reprogramming Software Card (orange color).
^ Use the Service Procedure steps to transfer ECM reprogramming data from the ASIST PC to CONSULT-II, and from CONSULT-II to the vehicle ECM.
^ Refer to the ECU Reprogramming Software Operations Manual (in ASIST) for additional information on using CONSULT-II for ECM reprogramming.
CAUTION
^ An ECM should be reprogrammed only when required by a specific Nissan Technical Bulletin, or as otherwise directed by Nissan North America.
^ The ECM can be permanently damaged if the reprogramming procedure is not followed exactly.
^ Do not disturb (don't touch) the vehicle, CONSULT-II, or the DLC-II cable while ECM reprogramming is in progress.
^ If the ECM is damaged, it must be replaced.
Reference: NTB00-006D
Date: May 12, 2006
ECM REPROGRAMMING FOR NISSAN VEHICLES
This amended version (NTB00-006d) updates the Service Procedure Section. Please discard all previously released copies of NTB00-006.
APPLIED VEHICLES: 1999 Frontier (D22)
1999 Quest (V41)
1999.5 Pathfinder (R50)
All 2000 and later
SERVICE INFORMATION
^ In-vehicle ECM reprogramming is available to update the ECM of certain 1999 vehicles (listed in Applied Vehicles above), and all 2000 and later vehicles.
^ This reprogramming allows the vehicle ECM to be upgraded to the latest operating specifications without removal or replacement of the ECM.
^ When an ECM has been reprogrammed it will display a new P/N on the CONSULT-II screen.
NOTE:
ECM reprogramming will not affect NATS.
^ ECM reprogramming requires the use of ASIST 8.0 or higher, and CONSULT-II with the ECU Reprogramming Software Card (orange color).
^ Use the Service Procedure steps to transfer ECM reprogramming data from the ASIST PC to CONSULT-II, and from CONSULT-II to the vehicle ECM.
^ Refer to the ECU Reprogramming Software Operations Manual (in ASIST) for additional information on using CONSULT-II for ECM reprogramming.
CAUTION
^ An ECM should be reprogrammed only when required by a specific Nissan Technical Bulletin, or as otherwise directed by Nissan North America.
^ The ECM can be permanently damaged if the reprogramming procedure is not followed exactly.
^ Do not disturb (don't touch) the vehicle, CONSULT-II, or the DLC-II cable while ECM reprogramming is in progress.
^ If the ECM is damaged, it must be replaced.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
