2002 Nissan-Datsun Frontier Base, AutomaticFACTORY OEM SERVICE PROCEDURE

Quick Lookups: Fluids

FLUID CAPACITIES
Fluid Type Application Standard Metric Fluid Spec Note S/H
Air Cond Compressor Oil 6.75 OZS. 0.19 L PAG 100 S
Air Cond Refrigerant 1.32 LBS. 0.59 KG R-134a S
Automatic Transmission Fluid 2.4L Eng 8.40 QTS. 7.94 L Genuine NISSAN Automatic Transmission Fluid Matic D, DEXRON III or MERCON S
Brake Fluid N/A N/A DOT 3 Brake Fluid S
Clutch Fluid N/A N/A DOT 3 Brake Fluid S
Differential Gear Oil 2.4L Eng C200 2.40 PTS. 1.13 L API - GL-5, SAE 80W-90 Standard differential gear: API - GL-5, SAE 80W-90, LSD gear: Use only LSD gear oil API - GL-5, SAE 80W-90. S
Engine Coolant 2.4L Eng,Automatic Trans w/Heater & Reservoir Tank 7.50 QTS. 7.09 L 50/50 mixture of Ethylene Glycol Base Antifreeze and water S
Engine Oil 2.4L Eng Drain and Refill,w/Filter 3.75 QTS. 3.54 L API - SAE 5W-30 API - SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0Deg.F (-18Deg.C). S
Engine Oil 2.4L Eng Drain and Refill,w/o Filter 3.50 QTS. 3.31 L API - SAE 5W-30 API - SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0Deg.F (-18Deg.C). S
Engine Oil 2.4L Eng Overhaul 4.50 QTS. 4.25 L API - SAE 5W-30 API - SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or SAE 10W-40 viscosity oils may be used if the ambient temperature is above 0Deg.F (-18Deg.C). S
Fuel Tank 21.15 GALS. 80.06 L S
Manual Transmission Fluid 2.4L Eng 4.25 PTS. 2.01 L Genuine NISSAN Manual Transmission Fluid (MTF) HQ Multi, SAE 75W-85 or API - GL-4, SAE 75W-85 S
Power Steering Fluid N/A N/A Genuine NISSAN Power Steering Fluid II or equivalent S
Windshield Washer Fluid N/A N/A Genuine NISSAN Windshield Washer Concentrate Cleaner and Antifreeze or equivalent Follow the Manufacturer's Instructions for the mixture ratio. S
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.