1992 Nissan-Datsun Sentra SE-RFACTORY OEM SERVICE PROCEDURE

Wheel Alignment Specifications

WHEEL ALIGNMENT SPECIFICATIONS

Application Preferred Range
Maxima
Camber (1)
Front -0.25 -1 To 0.5
Rear -0.58 -1.33 To 0.17
Caster (1) 1.25 0.5 To 2
Toe-In (2)
Front 0.08 (2) 0.04-0.12 (1 To 3)
Rear -0.08 (-2) -0.12 To -0.04 (-3 To 1)
Toe-In (1)
Front 0.18 0.1 To 0.27
Rear -0.17 -0.25 To -0.08
Toe-Out On Turns (1)
Inner 37 N/A
Outer 30 N/A
NX
Camber (1)
Front -0.25 -1 To 0.5
Rear -1.17 -1.92 To -0.42
Caster (1) 1.83 1.08 To 2.58
Toe-In (2)
Front 0.08 (2) 0.04-0.12 (1 To 3)
Rear 0.04 (1) -0.04 To 0.12 (1 To 3)
Toe-In (1)
Front 0.2 0.1 To 0.3
Rear 0.1 -0.1 To 0.3
Toe-Out On Turns (1)
Inner (1.6L) 41 N/A
Inner (2.0L) 35 N/A
Outer (1.6L) 33 N/A
Outer (2.0L) 30 N/A
Pathfinder
Camber (1)
Front 0.67 0.17 To 1.17
Caster (1) 1.3 0.8 To 1.8
Toe-In (2)
Front 0.16 (4) 0.12 To 0.2 (3 To 5)
Toe-In (1)
Front 0.32 0.23 To 0.4
Toe-Out On Turns (1)
Inner (3) N/A
Outer (3) N/A
Pickup (2WD)
Camber (1)
Front 0.42 -0.08 To 0.92
Caster (1) 0.37 -0.13 To 0.87
Toe-In (2)
Front 0.12 (3) 0.08 To 0.16 (2 To 4)
Toe-In (1)
Front 0.25 0.17 To 0.33
Toe-Out On Turns (1)
Inner (3) N/A
Outer (3) N/A
Pickup (4WD)
Camber (1)
Front 0.67 0.17 To 1.17
Caster (1) 1.3 0.8 To 1.8
Toe-In (2)
Front 0.16 (4) 0.12 To 0.2 (3-5)
Toe-In (1)
Front 0.32 0.23 To 0.4
Toe-Out On Turns (1)
Inner (3) N/A
Outer (3) N/A
Sentra
Camber (1)
Front -0.25 -1 To 0.5
Rear 0.92 -1.67 To -0.17
Caster (1) 1.42 0.67 To 2.17
Toe-In (2)
Front 0.08 (2) 0.04 To 0.12 (1 To 3)
Rear 0.04 (1) -0.04 To 0.12 (-1 To 3)
Toe-In (1)
Front 0.2 0.1 To 0.3
Rear 0.1 -0.1 To 0.3
Toe-Out On Turns (1)
Inner (1.6L) 41 N/A
Inner (2.0L) 35 N/A
Outer (1.6L) 34 N/A
Outer (2.0L) 30 N/A
Stanza
Camber (1)
Front 0.25 -0.5 To 1
Rear -0.58 -1.33 To 0.17
Caster (1) 1.33 0.58 To 2.08
Toe-In (2)
Front 0.08 (2) 0.04 To 0.12 (1 To 3)
Rear -0.08 (-2) -0.16 To 0 (-4 To 0)
Toe-In (1)
Front 0.2 0.1 To 0.3
Rear -0.19 0.38 To 0
Toe-Out On Turns (1)
Inner 36 N/A
Outer 29 N/A
240SX
Camber (1)
Front -0.75 -1.5 To 0
Rear -10.5 -1.6 To 0.6
Caster (1) 6.75 6 To 7.5
Toe-In (2)
Front 0.05 (1.3) 0.01 To 0.09 (0.3 To 2.3)
Rear 0.1 (2.5) 0.02 To 0.18 (0.5 To 4.5)
Toe-In (1)
Front 0.13 0.03 To 0.22
Rear 0.24 0.05 To 0.42
Toe-Out On Turns (1)
Inner 41 N/A
Outer 33 N/A
300ZX
Camber (1)
Front -0.83 -1.58 To -0.08
Rear -1.1 -1.6 To -0.6
Caster (1) 9.67 8.92 To 10.42
Toe-In (2)
Front 0.04 (1) 0 To 0.08 (0 To 2)
Rear 0.1 (2.5) 0.02 To 0.17 (0.4 To 4.4)
Toe-In (1)
Front 0.09 0 To 0.18
Rear 0.21 0.02 To 0.4
Toe-Out On Turns (1)
Inner 34.5 N/A
Outer 28.5 N/A
(1) Measurement in degrees.
(2) Measurement in inches (mm).
(3) Specification not available.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.