Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2024 Mitsubishi Eclipse Cross LEFACTORY OEM SERVICE PROCEDURE
Active Stability Control System (ASC) DTCS
ACTIVE STABILITY CONTROL SYSTEM (ASC) DTCS
| DTC | Description |
|---|---|
| C100A | FL Wheel Speed Sensor Circuit; DTC C1015: FR Wheel Speed Sensor Circuit; DTC C1020: RL Wheel Speed Sensor Circuit; DTC C102B: RR Wheel Speed Sensor Circuit |
| C1011 | FL Wheel Speed Sensor Signal; DTC C101C: FR Wheel Speed Sensor Signal; DTC C1027: RL Wheel Speed Sensor Signal; DTC C1032: RR Wheel Speed Sensor Signal |
| C1014 | FL Wheel Speed Sensor Performance; DTC C101F: FR Wheel Speed Sensor Performance; DTC C102A: RL Wheel Speed Sensor Performance; DTC C1035: RR Wheel Speed Sensor Performance |
| C1041 | FL Wheel Speed Tone Performance; DTC C1042: FR Wheel Speed Tone Performance; DTC C1043: RL Wheel Speed Tone Performance; DTC C1044: RR Wheel Speed Tone Performance |
| C1046 | FL Wheel Speed Sensor Phase; DTC C1047: FR Wheel Speed Sensor Phase; DTC C1048: RL Wheel Speed Sensor Phase; DTC C1049: RR Wheel Speed Sensor Phase |
| C104B | FL Inlet Valve; DTC C104F: FR Inlet Valve; DTC C1053: RL Inlet Valve; DTC C1057: RR Inlet Valve; DTC C105F: FL Outlet Valve; DTC C1063: FR Outlet Valve; DTC C1067: RL Outlet Valve; DTC C105B: RR Outlet Valve; DTC C1200: FL-RR Cut Valve; DTC C1204: FR-RL Cut Valve; DTC C1208: FL-RR Suction Valve; DTC C120C: FR-RL Suction Valve |
| C2104 | Valve Power Supply Circuit |
| C1073 | Motor Drive Circuit |
| C2116 | Pump Motor Voltage Low |
| C121D | Brake Fluid Pressure Sensor Circuit |
| C121E | Brake fluid pressure sensor |
| C1000 | Brake SW (Stuck) |
| C123B | System Control too Long |
| C2200 | ECU Internal Error |
| C2101 | Power Supply High Voltage |
| C1395 | Incomplete Brake Fluid Filling |
| C121C | Torque Request Signal Denied |
| C2206 | Re-execution of Variant Coding |
| C1210 | Longitudinal G Sensor Input Circuit |
| C1242 | Longitudinal G Sensor Signal |
| C123C | Sensor Cluster Malfunction |
| C1392 | Incomplete Learn (Longitudinal G); DTC C1393: Incomplete Learn Neutral (Lateral G) |
| C2204 | Sensor Cluster Internal Error |
| C1219 | Steering Angle Sensor Signal |
| C121A | SAS Initialization |
| C2205 | SAS Internal Error |
| C2002 | Valve Calibration not Completed |
| C1608 | EEPROM Fail |
| C1707 | Implausible Coding Data |
| C1800 | Acceleration/Deceleration Monitor |
| C1801 | Auto Stoplight Monitor |
| C1802 | ACC ECU Fail |
| C1803 | ACC Mode Off Disagreement; DTC C1804 ACC Deactivation Disagreement |
| C1805 | FCM/LDW/AHB Malfunction |
| C1806 | ACC/FCM target deceleration signal |
| C1807 | FCM/LDW/AHB target deceleration signal |
| U0100 | Engine CAN Timeout; DTC U0101 T/M CAN Timeout; DTC U0114 4WD CAN Timeout; DTC U0126 SAS CAN Timeout; DTC U0317 EPB CAN Timeout; DTC U15A0 ACC ECU CAN Timeout; DTC U15A5 FCM/LDW/AHB CAN Timeout |
| U0141 | ETACS CAN timeout |
| U0401 | Engine (CAN Message) |
| U0404 | AS & G (CAN Message) |
| U0417 | EPB (CAN Message) |
| U0428 | SAS (CAN Message) |
| U0435 | AWC (CAN Message) <Vehicles with S-AWC> |
| U0440 | Implausible AWC Data <Vehicles with S-AWC> |
| U1011 | ACC CAN Signal Error |
| U1013 | Driver Demand Torque Signal |
| U1015 | FCM/LDW/AHB Parity/Toggle Bit Error |
| U1073 | Bus-off |
| U1195 | Coding not completed; DTC U1197: Coding data unavailable |
| C1550 | ECU internal error; DTC C1554: Speed sensor is out of range; DTC C1555: Steering angle SNS.out of range; DTC C1556: Detection part abnormality; DTC C1608: EEPROM fail |
| U1073 | Bus-off |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
