Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Mitsubishi Eclipse L4-2.4L (4G69)FACTORY OEM SERVICE PROCEDURE
Programming and Relearning
STEERING WHEEL SENSOR CALIBRATION
CAUTION: After the next operation has been completed, carry out the following two operations:
1. Update the neutral point that the steering wheel sensor stores.
2. Reset the steering wheel angle correction value that the TCL/ASC-ECU stores.
^ Front alignment adjustment
^ Steering wheel sensor removal and installation
^ TCL/ASC-ECU replacement
CAUTION: Before carrying out the calibration, check if the steering wheel sensor-related diagnostic trouble code is set in the TCL/ASC-ECU.
Required Special Tools:
^ MB991958: Scan Tool (M.U.T-III Sub Assembly)
^ MB991824: Vehicle Communication Interface (V.C.I.)
^ MB991827: M.U.T-III USB Cable
^ MB991910: M.U.T-III Main Harness A
1. Park the vehicle on a level surface.

CAUTION:
To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
2. Connect scan tool MB991958 to the data link connector.
3. Turn the ignition switch to the "ON" position.
4. Select "Steering Angle Sensor".
5. Select "Special Function".
6. Select "Steering Angle Sensor Calibration".
7. Run "SAS Initialization". (Reusable parts only)
8. Select and run "Calibration".
9. Exit "Steering Angle Sensor" menu, and then select "ABS/ASC/ASTC".
10. Select "Special Function".
11. Select "Sensor calibration".
12. Select "SAS calibration".
13. Turn the ignition switch to the "LOCK" (OFF) position.
14. Disconnect scan tool MB991958.
CAUTION: After the next operation has been completed, carry out the following two operations:
1. Update the neutral point that the steering wheel sensor stores.
2. Reset the steering wheel angle correction value that the TCL/ASC-ECU stores.
^ Front alignment adjustment
^ Steering wheel sensor removal and installation
^ TCL/ASC-ECU replacement
CAUTION: Before carrying out the calibration, check if the steering wheel sensor-related diagnostic trouble code is set in the TCL/ASC-ECU.
Required Special Tools:
^ MB991958: Scan Tool (M.U.T-III Sub Assembly)
^ MB991824: Vehicle Communication Interface (V.C.I.)
^ MB991827: M.U.T-III USB Cable
^ MB991910: M.U.T-III Main Harness A
1. Park the vehicle on a level surface.
CAUTION:
To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
2. Connect scan tool MB991958 to the data link connector.
3. Turn the ignition switch to the "ON" position.
4. Select "Steering Angle Sensor".
5. Select "Special Function".
6. Select "Steering Angle Sensor Calibration".
7. Run "SAS Initialization". (Reusable parts only)
8. Select and run "Calibration".
9. Exit "Steering Angle Sensor" menu, and then select "ABS/ASC/ASTC".
10. Select "Special Function".
11. Select "Sensor calibration".
12. Select "SAS calibration".
13. Turn the ignition switch to the "LOCK" (OFF) position.
14. Disconnect scan tool MB991958.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
