Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2004 Mitsubishi Lancer EvolutionFACTORY OEM SERVICE PROCEDURE
Disc Brake Specifications
WARNING: This page is about a different car, the 2004 Mitsubishi Galant. However, it is still accessible from the selected car via links, so may be relevant.
BRAKE SPECIFICATIONS
| Application | In. (mm) | ||||
|---|---|---|---|---|---|
| Brake Booster | |||||
| Effective Diameter Of Power Cylinder | 8 + 9 (205 + 230) | ||||
| Boosting Ratio | 6.5 | ||||
| Push Rod Protruding Length | (1) .405-.414 (10.28-10.52) | ||||
| Brake Pedal Height | 6.69-6.80 (169.8-172.8) | ||||
| Brake Pedal Free Play | .12-.31 (3-8) | ||||
| Brake Pedal-To-Floor Clearance (Minimum) | 4.33 (110) | ||||
| Master Cylinder Inside Diameter | 1.00 (25.4) | ||||
| Proportioning Valve Output Fluid Pressure (Models Without ABS) - psi (kPa) | |||||
| Split Point | 534-605 (3680-4170) | ||||
| When Input Fluid Pressure Is 1139 psi (7850 kPa) | 760-833 (5240-5740) | ||||
| Proportioning Valve Output Fluid Pressure Difference Between Left & Right (Models Without ABS) (Maximum) - psi (kPa) | 73 (500) | ||||
| Front Disc Effective Diameter | |||||
| 2.4L | 8.7 (222) | ||||
| 3.8L | 9.5 (241) | ||||
| Front Caliper Cylinder Inside Diameter | 2.4 (60.3) | ||||
| Rear Disc Effective Diameter | 8.7 (222) | ||||
| Rear Caliper Cylinder Inside Diameter | 1.4 (34.9) | ||||
| Disc Runout (Maximum) | |||||
| Front | .0039 (.1) | ||||
| Rear | .0016 (.04) | ||||
| Maximum Disc Brake Drag Force - Lbs. (Kg.) | |||||
| Front | |||||
| 2.4L | 12 (5.44) | ||||
| 3.8L | 14 (6.35) | ||||
| Rear | 12 (5.44) | ||||
| Front Disc Thickness | |||||
| Standard | 1.02 (26) | ||||
| Minimum | .96 (24.4) | ||||
| Rear Disc Thickness | |||||
| Standard | .39 (10) | ||||
| Minimum | .33 (8.4) | ||||
| Pad Thickness | |||||
| Standard | .39 (10) | ||||
| Minimum | .08 (2.0) | ||||
| Hub End Play | .002 (.05) | ||||
|
|||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
