Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Mitsubishi Lancer EvolutionFACTORY OEM SERVICE PROCEDURE
Ignition Timing: Diamante
- Connect scan tool to OBD-II Data Link Connector (DLC) located below instrument panel, to right of steering column. See Figure. Install timing light. Start and warm engine until engine coolant temperature is 176-203°F (80-95°C). Turn lights and accessories off. Put automatic transmission in Park or manual transmission in Neutral. Insert a paper clip into No. 3 terminal of 3 pin connector as illustrated. See Fig 1. Connect a primary voltage type tachometer to paper clip.
- Allow engine to idle. Check and ensure engine curb idle speed is within specifications for timing check. Read base ignition timing value. See IGNITION TIMING SPECIFICATIONS (Degrees BTDC @ RPM) table.
- Using scan tool, select MFI SYSTEM ACTUATOR TEST, then select item No. 17 (BASIC IGNITION TIMING). Press "Y" key and check basic ignition timing. If basic ignition timing is within specification, go to next step. If basic ignition timing is not within specification, cancel MFI system actuator test and check for DTCs. See appropriate SELF-DIAGNOSTICS article. Check timing belt cover and Crankshaft Position (CKP) sensor installation. Check CKP sensor sensing blade condition. Repair as necessary.
- Cancel MFI system actuator test. Read actual ignition timing value. See IGNITION TIMING SPECIFICATIONS (Degrees BTDC @ RPM) table.
CAUTION:
MFI system actuator test must be cancelled after basic ignition timing check or test will continue to run for 27 minutes. Driving vehicle under this condition may damage engine.
IGNITION TIMING SPECIFICATIONS (Degrees BTDC @ RPM)
| Application | Base | Actual | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Diamante | 2-8 @ About 700 | (1)(4) 10 @ About 700 | |||||||||
| Eclipse | |||||||||||
| 2.4 | 2-8 @ About 700 | (1)(3) 10 @ About 700 | |||||||||
| 3.0L | 2-8 @ About 700 | (2)(3) 15 @ About 700 | |||||||||
| Galant | |||||||||||
| 2.4L | 2-8 @ About 700 | (1)(3) 10 @ About 700 | |||||||||
| 3.0L | 2-8 @ About 700 | (1)(3) 15 @ About 700 | |||||||||
| Lancer | 2-8 @ About 700 | (1)(3) 8 @ About 700 | |||||||||
| Montero | 2-8 @ About 750 | (1)(3) 10 @ About 750 | |||||||||
| Montero Sport | 2-8 @ About 700 | (2)(3) 10 @ About 700 | |||||||||
| Outlander | 3-7 @ About 700 | (1)(3) 10 @ About 700 | |||||||||
|
|||||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
